glueman Posted April 30, 2020 Share Posted April 30, 2020 Hi everyone, I’m struggling trying to get the right consistency of paint (paint to thinner) for my airbrush. I’m using a KKmoon AB at 18-20psi. I’m trying to get a ratio of about 60:40 thinners to paint as follows. I have a thimble that I use to measure out the paint: half thimble xf83 + half thimble x22. I mix that with one full thimble of Tamiya thinners. That should give me a 50:50 thinners to paint ratio but the paint is always way too thin when on the model. I’m at a loss as to why the paint is so thin every time. Hope someone can point me in the right direction. Many thanks Pete Link to comment Share on other sites More sharing options...
Kev The Modeller Posted April 30, 2020 Share Posted April 30, 2020 50/50 is really I starting point for Tamiya acrylics I find, depending on what you're doing. The paint will be thin, you need to build up the layers 2 or 3 is normally all you need. Take a look at This and This Link to comment Share on other sites More sharing options...
TimB Posted April 30, 2020 Share Posted April 30, 2020 A tip I picked up from a demo at SMW several years ago was to mix the paint in the airbrush cup. Add the thinner then use an old but sound paintbrush to transfer paint to the cup and mix it. It allows very great variation in thinner: paint ratio and allows you to see what the mix is doing. You can test it easily, and if you over thicken it a few drops of thinner can correct it. Your first spray run tends to be a bit more thinner until the paint arrives at the nozzle, but that is not a bad thing. The technique also supports really mixing small amounts of paint for detail work. Of course, if you want a custom mix for a large area you either need to count the brush loads accurately or mix the basic paint first. I found that using this route really helped me take control of the airbrush, and develop a feel for how the different paint/thinner mixes behave. For example, Tamiya with its own thinner does not spray the same as it does thinners with Gunze self levelling thinner, so I change ratios until it feels about right. I pre-mix certain things like Halfords Appliance White, but 90% of my painting is done mixing paint and thinner in the airbrush cup. Regards Tim Link to comment Share on other sites More sharing options...
glueman Posted April 30, 2020 Author Share Posted April 30, 2020 Thank you Kev for the link to the videos, and also Tim for the brush tip. Do you add the thinner with a brush (before the paint) or do you use a pipette? Cheers Pete Link to comment Share on other sites More sharing options...
TimB Posted May 1, 2020 Share Posted May 1, 2020 Hi, Pete. I use a pipette for the thinner, but don't dip it in the "mix" so it stays clean. Regards Tim Link to comment Share on other sites More sharing options...
Kev The Modeller Posted May 2, 2020 Share Posted May 2, 2020 I put the thinner into the colour cup first, then the paint and mix. Link to comment Share on other sites More sharing options...
Steve Noble Posted May 2, 2020 Share Posted May 2, 2020 (edited) I use some small metal mixing trays from Gunze that are perfect. Add thinner with a pipette and transfer paint with a wooden coffee stirrer one drop at a time to the required quantity. Then simply mix well and pour into the airbrush. Wipe the metal tray out with thinner, they are reusable and last forever.. Edited May 2, 2020 by Steve Noble Link to comment Share on other sites More sharing options...
CharlieNZ Posted May 3, 2020 Share Posted May 3, 2020 You don't think the fact half your paint is made up of clear gloss might be affecting how thin it appears? It's going to be much less opaque, regardless of viscosity. I like mixing X22 with Tamiya matt paint as it sprays much better, but I use perhaps a 1:5 ratio, just adding a couple of drops into my colour cup after thinning the paint in the cup to the desired consistency. TBH, at 18-20 psi, you should be able to get away with less thinner than 50/50. Link to comment Share on other sites More sharing options...
Steve Noble Posted May 3, 2020 Share Posted May 3, 2020 I thought x22 was thinner? Didn't realise you were mixing with x22 clear gloss? If that's what you're doing you'll make the paint translucent and it will appear thin and won't cover very well as the x22 gloss will make it see through... Link to comment Share on other sites More sharing options...
Rabbit Leader Posted May 3, 2020 Share Posted May 3, 2020 Was just going to say, I reckon the X-22 is the problem here. I take a clean plastic ‘party’ shot glass and put my thinner in first (Gunze’s Mr. Color Leveling thinner). I’ll then add the paint to the thinner and mix until I’m happy. Pour the thinner / paint mix into the AB cup and adjust your air as required. Once your’e happy, spray some thinned Clear X-22 over the top to protect your paint and apply your decals. Cheers.. Dave Link to comment Share on other sites More sharing options...
Steve Noble Posted May 3, 2020 Share Posted May 3, 2020 So I don't understand the addition of the x22 clear? Are you trying to make a matt paint into gloss? If so it's much easier to simply apply the x22 over the matt paint and not mix it into the matt paint.. Link to comment Share on other sites More sharing options...
glueman Posted May 3, 2020 Author Share Posted May 3, 2020 Thanks everyone for your comments. The X22 ... I was following some of the paint schemes described in the Sci-Fi work in progress which described adding X22 to the matt paint. Hopefully, I will get round to doing more tests over the next few days. I can build ... but I can't paint. Bane of my modelling life Pete Link to comment Share on other sites More sharing options...
glueman Posted May 7, 2020 Author Share Posted May 7, 2020 Having watched a few videos on YT I'm now trying out the droplet method whereby I add thinners (first) and paint (second) to the AB cup by counting droplets from a pipette. I've been using the ratio 2 (paint) to 1 (thinners) mixing in the AB cup (10 droplets thinner - 20 droplets paint). Results are brilliant, much better than before. Also ... I've splashed out and purchased a Neo for Iwata AB ... and boy does that make a big difference. Using the right tools for the job certainly does help to build confidence. Thanks again for all your helpful suggestions. Pete 2 Link to comment Share on other sites More sharing options...
Lewis95 Posted May 14, 2020 Share Posted May 14, 2020 Hmm.... I found I had excellent coverage on a 3:2 thinner/paint droplet ration. 3 drops of thinner to 2 drops paint. Albeit, I did go over a primer coat of Surfacer 1500. Absolutely amazing coverage and ecstatic with it after just one coat. Albeit, this was with a lacquer thinner. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now