Mike Posted June 4, 2016 Share Posted June 4, 2016 Chieftain Marksman SPAAG1:35 Takom The Marksman system was developed by Marconi to be a drop-in solution to the need for mobile, radar-targeted anti-aircraft gun platforms for close-in support of troops, installations and other valuable assets. Although the turret could be mated with many different hulls, the British chose the Chieftain tank for trials of this twin 35mm cannon equipped system. The second prototype was mounted on a Chieftain, and have the vehicle a top-heavy look, with the crew hatches perched high on the top of the turret, overshadowed by the radar dish that made it so accurate to its maximum range of 4,000m.Sadly, the Chieftain installation never progressed beyond prototype and it didn't see service with the British Army. The turret did see limited service with other operators such as Finland who mounted it on an uprated T-55 chassis.The KitThis is a re-tooling of the new Chieftain kits that were released late last year and were reviewed here. Some of the previous turret parts have been included through necessity and because of their placement on the various sprues, but the majority of the new plastic is SPAAG related. Inside the nicely decorated box are five large sprues, two hull halves and track parts that are common to all the Chieftain boxings, plus three new sprues, three of which are small, specific to the Marksman, with six parts on their own spruelets. The Photo-Etch (PE) is common with the Mark 10/11s, and the decal sheet is new for the kit, with one factual number plate and a couple more for hypothetical, or "what if" schemes. The common parts are identical to the previous issue, and the building of the lower hull proceeds in exactly the same way as before, which you can read about in the previous reviews. The new parts have the same level of detail, and portray the slab-sided Marksman turret nicely, including the turret ring adapter, which hints at the inclusion of the Marksman parts in possible future projects… maybe a T-55M? Speaking of the turret ring, the height of the cylindrical section seems just a shade too short in the vertical. A shim of plastic card between the ring and the bayonet insert should be able to make that good though, if you agree and feel up to the task. Assuming you have the hull completed, there are four bullet-splash protection strips to remove, which are replaced by raised sections that fit to the hull via pegs that fit into holes drilled from inside beforehand. After that the turret adaptor ring is inserted and that's the hull changes covered! The turret is then started, with the guns built up first from two halves that have some lovely moulding that results in a hollow flash-guide as per the real thing. These then fit onto a five-part breech fairing that has an axle for joining to the turret body. The two interlock in the middle of the turret, but as there is nothing to provide a friction-fit braking on the pivot-points, you will have to either fabricate your own, or glue them in position, or they will flop. The lower turret with moulded in ring closes up the turret, whilst providing the floor of the bustle that is added later from a single part. A number of sensors and vision devices are installed on the top, along with an insert that contains the two crew hatches and forms the base of the radar installation. The top section of the insert flips up on a pair of hinges for stowage of the radar during travel. More small parts such as smoke dischargers and antennae mounts are added on the sides of the turret and then the tapered radar base is inserted on the hinged panel along with the motor housing. The radome and receiver are put together with some additional sensors on the head-unit, which must again be glued in position. The turret ring then has its bayonet-fitting added to the bottom, which is where the shim of styrene would go if you wanted to raise it a little. When dry the turret is fitted to the hull and twisted to engage the bayonet lugs.MarkingsAs is now traditional with a Takom release, there is a separate concertina-fold booklet for colour and markings instructions that has been done in conjunction with AMMO of Mig Jiménez. There are five schemes in the box, and all bar the green one are fanciful, assuming the Marksman equipped Chiefy had gone into service. From the box you can build one of the following: NATO Green/Sand Yellow camo. NATO Green/Black camo. NATO Green all over. Sand Yellow all over. Green, Grey Blue, White, Olive Drab Berlin Brigade urban scheme. Colour call-outs are in AMMO codes, but the common names are also provided, so if you don't use them or can't source them, you can easily convert the colours. The decals are printed anonymously on a small sheet, but are to a high standard with good registration, colour density and sharpness. They've even printed two small Union flags, which are the right way up… just don't apply them upside down after they went to all that trouble!ConclusionA good use of the existing tooling to create a nice canvas for a What-If, or just a bit of fun with different schemes. Overall the shape of the turret seems good, with the aforementioned narrow band around the bottom, and the quality of the parts matches perfectly with the common parts.Highly recommended. Review sample courtesy ofUK Distributors for 3 Link to comment Share on other sites More sharing options...
Alpha Delta 210 Posted June 4, 2016 Share Posted June 4, 2016 Interesting choice of subject and good to see that Takom have included the markings for the Marksman preserved in running condition at Duxford. Link to comment Share on other sites More sharing options...
Antoine Posted June 4, 2016 Share Posted June 4, 2016 The turret did see limited service with other operators such as Finland who mounted it on an uprated T-55 chassis. It would be nice of Takom to mix this turret with their T-55 hull. Link to comment Share on other sites More sharing options...
Julien Posted June 4, 2016 Share Posted June 4, 2016 Mike was only saying that earlier. Lets hope they do it. Julien Link to comment Share on other sites More sharing options...
Sgt.Squarehead Posted June 4, 2016 Share Posted June 4, 2016 Sgt. York's British cousin.....I guess? Link to comment Share on other sites More sharing options...
Julien Posted June 5, 2016 Share Posted June 5, 2016 Sgt. York's British cousin.....I guess? Yes, but only the German side of the family amounted to anything 1 Link to comment Share on other sites More sharing options...
Mike Posted June 5, 2016 Author Share Posted June 5, 2016 With Takom releasing a T-55 line of kits, I reckon it's just a matter of time before we see the Finnish ItPsv 90 Link to comment Share on other sites More sharing options...
Panzer Vor!!! Posted June 26, 2016 Share Posted June 26, 2016 The turret was designed to fit the T54/55.59/62/72 Amx 30 Centurion Chieftain Challenger M60 series Phew Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now