Search the Community
Showing results for tags 'xl360'.
Good afternoon all! Finally. Finally I have completed this build, as I am sure many of you know the old Airfix Vulcan kit is in need of a re-tool and in its current state it requires A LOT of work! So, shall we begin? Kit: -Airfix Avro Vuclan 1:72 Aftermarket: -White Ensign Model (WEM) Interior -WEM Bomb Bay -WEM Exterior (airbrakes, landing gear PE inserts) -Freightdog Exhausts Scratchuilt Items: -ECM bay -Interior of canopy (although I forgot to photograph this, it has a bulkhead built in with some texturing added to the interior) Paints: -Vallejo Model Air (the majority of paints were mixed to obtain the required colours) Weathering: -Vallejo panel wash -AK Interactive engine oil wash *Edit: Decals: -Freightdog- RAF Neptunes and Avro Vulcans WIP here, if you want: Click Here Picture time! (Don't worry I do not support the politics of East Germany! I just have obsession with Cold War history! ) Thanks for stopping by! Kind regards, Sam
Good morning! The postman dropped off the photo-etch pieces this morning so I thought I might as well start So, the base kit will be the old Airfix 1:72 Avro Vulcan, with aftermarket bits including: -Freightdog Resin 201 Series Tailpipes -White Ensign Models (WEM) Vulcan Interior -WEM Vulcan Exterior -WEM Vulcan Bomb Bay This build will be significant for two reasons; first of all, with AS exams starting in two weeks and proceeding over the next couple of months, it will be something to keep me sane! Secondly, it will be the first build where I've already had a go at doing some build-enhancing techniques before and needless to say I shall attempt to use these on this build, these include: using filler to get rid of those nasty gaps, using a scribing tool (Tamiya) to replace the notorious raised panel lines, working with resin aftermarket pieces and finally working with photoetch (I might have thrown myself into the deep end with this one!) XL360 is my second nearest Vulcan, the closest being Cosford, I have chosen this one because it's preserved (and has served) as a 617 "Dambusters" aircraft, I have also had the pleasure of sitting in the rear cockpit of the aircraft- I therefore have quite a bit of reference material to hand and finally because, unlike the shiny Cosford example, the Coventry Vulcan allows me to have a shot at weathering. Pre-build photos: Well, more updates shall follow in due course, don't expect them to be too frequent, unfortunately revision must take precedence over the next few weeks. Kind regards, Sam
Good morning, I just thought I might ask the advice and opinions of members of the forum in regards to a project i'm starting. I was thinking of doing a 1:72 Airfix Vulcan "properly"; with aftermarket engines, intakes (possibly, you'll see later) and the white ensign model (WEM) stuff. I've also thought it might be an appropriate model to do some rescribing for the first time, along with flory washes, photo etch and resin- I had to choose this model So the few questions I would like to ask are as follows: 1. Can you use a steel ruler and is it adviseable for linear panel lines as a guide- rather than masking tape? 2. (Perhaps the most important decision) Which Vulcan to do?! I've got a choice between XH558 and XL360- having been in XL360 and purely because I quite like the 617 tail marking (I might be turning into an "anorak" ) I feel a greater sense of attachment to her, although I have seen XH558 display at Throckmorton last year and so I am quite keen on her too! 3. Should I have "everything" open (gear down, airbrakes down, bomb bay doors open, crew hatch open)? Or should I save some money and (if I should choose XL360) build the Coventry Vulcan as it currently is (and save additional money with FOD covers for the ghastly kit intakes)? Note: I would have built the Cosford Vulcan but I'm not keen on the highly glossed finish of XM598 4. Any other advice for building the Airfix kit? Joins to watch out for, etc. I know that 2 and 3 are very subjective points but I would greatly value your opinions. Many thanks, Sam Edit: the 617 tail marking on XL360 Edit 2: -Are there any definitive colour matches out there for either 558 or 360?