Jump to content

Curtiss Condor by Glencoe: Now Brought To You In Living Color....


Recommended Posts

Posted (edited)

Starting in on the wings, fellas....

 

A final bout of measure and arithmetic led to the conclusion each upper wing panel ought to be extended by 7mm, and each lower wing panel by 5mm. .This brings the spans up to within 4% of scale. The lower wing center section is underscale by just a couple of millimeters, which I will live with, and if one takes the upper wing center section running from aileron to aileron, this, too, is only short by about the same measure.

 

I put the cut in mid-panel, as there will be work needed to put in dihedral where panel meets center section.

 

d2mShWx.jpeg

 

rITYmmg.jpeg

 

I hoped to use a tab, as I had earlier on the lower wing nacelle to fuselage gap. I thought I could slide to the mark, set, and then fit sheet bent to a curve into the gap. It was hard to line up properly, the hollow in the wing section wasn't as commodious as on the lower center, so the tab was thinner, and snapped under strain of attempts at fine adjustment.

 

So I split the tip section on the seam, curved strips of 30thou sheet and attached them, top and bottom.

 

HhcCaB9.jpeg

 

The whole thing was getting a bit haggled by now, and the strips clearly would not stand up to necessary work. So I stuffed them solid enough with bits of scrap and CA gel.

 

IKiQg8V.jpeg

 

It didn't need undue sanding when joined.

 

BWJku4w.jpeg

 

The patch extension is just butted to the central piece. It's pretty solid, but not to be dropped, and I'll have to be careful to grip and work on the same side of these. There'll be three more, I expect I'll get better at it as I go. I'm pretty sure I can do the dihedral without a full cut.

 

 

James

Edited by Old Man
  • Like 12
Link to comment
Share on other sites

  • Old Man changed the title to Curtiss Condor by Glencoe: Wing Extensions Started
4 hours ago, Corsairfoxfouruncle said:

You're a better man than me, I couldn't do that kind of work and would just live with the length issues. Id be afraid of doing something that couldn't be fixed. 

 

Thanks, Uncle.

 

In for a penny, in for a pound. It's kind of fun.

 

Though I haven't managed one in a while, I've done a lot of scratch-building, and figure I can repair or replace most anything. I may be wrong, but it widens the horizon and steadies the nerves....

 

 

James

  • Like 4
Link to comment
Share on other sites

26 minutes ago, Old Man said:

 

Thanks, Uncle.

 

In for a penny, in for a pound. It's kind of fun.

 

Though I haven't managed one in a while, I've done a lot of scratch-building, and figure I can repair or replace most anything. I may be wrong, but it widens the horizon and steadies the nerves....

 

 

James

I actually want to do stuff like this. One I need is an 1/48 F-86H but no one makes one. So I would need to heavily modify and cross two other versions to get what I need. 

Link to comment
Share on other sites

14 hours ago, stevehnz said:

There are other ways.... :D

Steve.

 

58 minutes ago, Old Man said:

That there are, Sir....

..although they tend to be expensive 😇

  • Haha 2
Link to comment
Share on other sites

On 5/16/2024 at 7:38 AM, Toryu said:

A good surgeon you are!

 

 

I was kind of lucky the dimension came out right. Next pass will be more precise.

 

I'm going to put it aside a bit and get in a start on my Grumman now that the fleet's in.

 

 

James

Link to comment
Share on other sites

Good to see some close attention to this kit. I must admit I don't temember the problem of the engine nacelles in different places. But then again I am a 'looks about right' modeller so probably fudged it somehow. Will keep an eye on your build 😊

  • Like 1
Link to comment
Share on other sites

  • 2 weeks later...
Posted (edited)

Got the wings extended, and given them their dihedral.

 

Here's the upper wing.

 

jQ5VGeH.jpeg

 

Dihedral break is at the inner end of the ailerons.

 

Here's the lower wing, top and bottom. Dihedral break is just outboard of the nacelles. The under surface is sawed through, the upper surface is scored, and bent to proper angle. Lower wing dihedral is greater than the upper wing's.

 

x6gORHA.jpeg

 

B45sFMs.jpeg

 

Here's the upper wing. I'm using the Tamiya Camel Yellow as a primer/base coat.

 

vHDZBVj.jpeg

 

Here is the lower wing, under primer.

 

zla8QrP.jpeg

 

At this point I figured I'd had enough aromatic hydrocarbons to last a few days, and went on to other projects. Should be back to it next weekend.

 

This is the last alteration, from here on it's surface detailing, assembly, scratching a part here and there.

 

 

James

Edited by Old Man
  • Like 10
Link to comment
Share on other sites

  • Old Man changed the title to Curtiss Condor by Glencoe: Wing Extensions Done And Dihedral Set
19 hours ago, Corsairfoxfouruncle said:

Looking forward to the next stages. 

 

 

So am I, Uncle. Glad to have the tweaks out of the way.

 

 

James

  • Like 1
Link to comment
Share on other sites

  • 2 weeks later...

Getting things squared away to paint took some effort, but nothing worth photographing. Here's the start of serious painting....

 

JdPjuFm.jpeg

 

The rattle-can yellow has been gone over with dark (reddish) Cadmium Yellow, the Olive Drab is a mix of black and a yellow ocher. Here's things after several coats:

 

lpJnMgW.jpeg

 

ftgUImr.jpeg

 

The cockpit roof has been attached:

 

tQNzl4A.jpeg

 

Eujrxsk.jpeg

 

The fit of lower wing to fuselage looks good from here:

 

xXUJD28.jpeg

 

Less so from here:

 

XTKEeN8.jpeg

 

And if I showed you the thing head-on it would make you weep. When firmly seated, the wing slants, starboard low, port high. This may be a 'me' problem, not a kit problem. I don't know what distortions my braces raising the dorsal spine may have wrought. A 30thou shim seems to fix it:

 

 

 

vz6AIA0.jpeg

 

NmkKeER.jpeg

 

The slot under the nose is emergency surgery. In handling, I managed to depress the rear starboard cockpit glazing. It was still hanging by its top joint, and the slot let me insert a toothpick to push it back into place.

 

t07wKMy.jpeg

 

HP9iSBl.jpeg

 

So far as I can tell, I have been able to dress all seams about the glazing without scratching the clear.

 

Next will be motors, and some decals. May even get to struts next pass....

 

 

James

 

 

 

 

 

 

  • Like 6
Link to comment
Share on other sites

  • Old Man changed the title to Curtiss Condor by Glencoe: Now Brought To You In Living Color....
28 minutes ago, Corsairfoxfouruncle said:

 Nice save on the glazing, sorry to hear of the wing imbalance. With all the work thats been done anything could be ever so slightly out and it will throw things off. 

 

 

The wing was an unpleasant surprise, Uncle. I was looking at the thing with an eye towards fit at the roots. I want the motors on before attaching the wing, and that means a good dozen blue and yellow stripes.

 

I think I've got a good shot at making the Gallery here.

 

 

James

Edited by Old Man
  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...