Jump to content

Coyote TSV Update Set (36489 for Hobby Boss) 1:35


Mike

Recommended Posts

Coyote TSV Update Set (36489 for Hobby Boss)

1:35 Eduard

 

boxtop.jpg

 

We reviewed this new kit from Hobby Boss here a couple of months ago, and it’s a nicely detailed kit of the British Army’s modern armoured support vehicle.  This Photo-Etch (PE) detail set from Eduard is designed to improve on the detail that’s available in the kit, taking advantage of the thin etched brass to make in-scale parts.  The set arrives in an A5 sized resealable clear foil bag, and consists of a single large fret of brass that is filled with a host of goodies.

 

36489.jpg

 

Two large skins are supplied for the inner sides of the main load area, and the undersides of the rear wheel wells are similarly skinned with a new part each, which also has a replica of flexible rubber “frill” that helps to keep the dust and aggregate from kicking up when in motion.  When the glue is dry, you are advised to push the edges to give it a more organic look to better replicate the real rubber, so check your references if you’re unsure how they should look.  A similar wheel arch insert with simulated rubber edges is supplied for the front arches too.  The front of the vehicle and centre section stowage boxes between the cab and load area is covered with tie-down loops, all of which are removed and replaced with new PE parts with better detail.  The running boards down the side of the vehicle have PE mesh included in the box, but the replacements in this set are more defined and to be honest, more capably etched.  The seatbelts for the crew will stop them from getting thrown clear of the vehicle at the first bump, and four sets are included for all the crew, then the same courtesy is afforded to the big .50cal ammo cans around the gunner’s platform, which are lashed down on trays that are absent from the kit, so you’ll need to cut off the pins for the ammo boxes, glue the trays in place, then add the ammo boxes back, lashing them down if you wish.  Another tray for a ready ammo can is included for the gunner’s ring, which again fits in place over the two locating pins once they are removed.  The rear of this platform is covered with pioneer tools, all of which get new clasps after a short chop to remove the chunky mouldings.  Next to these tools, a box is skinned over to include a mesh panel in the centre that is missing, as is a circular part on the floor behind it.  A couple of weapon lashing points are added to the other side of the hump.

 

The kit includes a large single part to represent a stowage box that is fixed to the A-frame door on the starboard side of the vehicle, and most of this part is removed, leaving the narrow top section to be reused.  A new lower section is made up from PE panels, with internal load crates that have tie-down straps across their fronts.  Lashings for a spade are added to the underside, then the top section of part D58 is glued atop the new assembly to complete it, giving the area much better scale authenticity.  On the opposite side of the vehicle the similar framework “door” carries the spare tyre, which is fitted to its mount with a new PE bracket and large retaining nut for extra detail.  The crew cab doors are detailed with additional small parts too, with the work duplicated on both sides, and new wire-cutters replacing the chunky kit mouldings on the sloped front roll cage around the cab.  On the sides a pair of “shopping bags” made from strapping are made up from the etched parts on the fret, looped through itself and fitted on the two positions on the right side of the vehicle, adding some contents if you feel the need.  At the rear of the Coyote, the two extensions that overhang the rear of the vehicle’s light clusters are replaced by a new PE pair, with mounts for the kit’s grenade dispensers with a more realistic hollow underside and scale thickness.

 

example.jpg

 

The last area to be detailed is the antenna forest that is carried over the stowage in the middle of the vehicle behind the drivers.  The kit platform is slightly incorrectly positioned, so it is replaced by a new assembly that consists of a flat top surface that has double-folded edges for strength, and is further stiffened by adding cross-braces and C-section stringers to the underside.  On the flat top surface, an additional sensor is made from 2mm rod from your own stock with a circular base, and some of the other kit antennae are also placed on raised “washers”.  This is then fixed to the two supports as shown on the final diagram.

 

 

Conclusion

A very comprehensive upgrade set for what is already a nice kit.  The extra detail will definitely set your model aside from all the others.

 

Highly recommended.

 

bin.jpg

 

Review sample courtesy of

logo.gif

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...