Jump to content

Avro Manchester Bomber Instrument Panel 1:1


Recommended Posts

Carl, Isn's comment below reminded me of something I wanted to mention earlier regarding the Morse Key light switch that you did a few weeks ago. The cipher (flashing Morse Code) used by the Allies when they flew over the invasion fleet off the Normandy coast was dit-dit-dit-dah or dot-dot-dot-dash, code for the letter V in the English alphabet.

 

The code "V" stood for Victory (Allied Victory). It was tapped out to the rhythm from the opening of the Fifth Symphony of Ludwig van Beethoven, who as you know was a very great German composer. I think there was a bit of irony in choosing that code, which was probably understood by most airmen at the time, but it’s meaning may have been forgotten over the last 79-years.

 

Harold

 

On 1/14/2023 at 7:18 AM, Brandy said:

Gorgeous work here. If it's almost impossible to tell the original from the replica then you must be doing something right!

I also learnt something about morse light signalling!

 

Isn

 

Edited by Sergeant
  • Like 1
Link to comment
Share on other sites

23 hours ago, alzictorini said:

Evening BM’s

 

The dayglo paint arrived, mint

Whilst I was waiting for the paint, I cracked on with the Bomb Jettison handle (another jettison handle – I know). I found a few pics on-line and this is all the handle looks like:

 

Lanc-Jettison-1-large.jpg

 

The one above is a straight pull but ours comes out of the panel at 45 degrees and faces the pilot.

Again, I designed what I saw in fusion and began to print. This took about 1,5 hours to print so I did not make a cast, here are the first few items of the bed:

 

20230114-152412.jpg

20230114-152300.jpg

20230114-182557.jpg

 

A quick test fit showed it all came together perfectly. Just a sand down clean up and paint:

 

20230114-182502.jpg

 

Whilst the aluminium paint was drying on the Handle I stuck on my graphic to the Suction gauge and painted the dayglo onto the numbers requiring it:

 

20230114-182519.jpg

 

Both items painted and complete:

 

20230114-182440.jpg

 

As 12jaguar mentioned, mine glow the same as the real items did but with zero radiation issues:

 

20230114-182415.jpg

 

Enjoy

Good morning, Carl. Excellent results on the moulding, graphics, and paint work above. Also thank you for the size information on your square gauges, I was thinking they were a bit larger. The HP 555 Inkjet printer does a great job with your graphics. I have an ancient HP 2540 printer (2013) that I would like to replace with something like you have, but that 'dog' of a printer will not die.

 

Is the purpose of the Bomb Jettison handle to get rid of unused bombs before returning to base, or does it have something to do with bombs hanging up in the bomb bay?

 

Harold

Edited by Sergeant
Link to comment
Share on other sites

Thank you, Carl. I take those instructions to mean the jettison handle was used to release the entire load of bombs so the aircraft could make a safe landing.

 

Harold

 

Edited by Sergeant
Link to comment
Share on other sites

Evening BM's

 

Next on the list is the MkVIII Oxy Regulator. Looking at the panel pic from the pilots notes it looks like the early A model on the MKI Manchester. Looks something like this:

 

here's a real item on ebay:

 

download.jpg

 

I've made plenty of these in the past so it shouldn't be too difficult to make, just need to find the old moulds??? Oh yes:

 

20230116-203045.jpg

 

Got some other parts in the spare box already made (and some evergreen sheet for it all to go on):

 

20230116-203019.jpg

 

Again the name plate was already made in the spares box:

 

20230116-222945.jpg

 

Little bit of paint here and there:

 

20230116-203036.jpg

 

Test fit:

 

20230116-222820.jpg

 

I have run out of black die for the casting so I cast the gauges in natural white, ill have to spray them black tomorrow:

 

20230116-222759.jpg

 

Looking good, should have it finished by tomorrow??

 

Enjoy

  • Like 11
Link to comment
Share on other sites

Evening BM's

 

Just finished the MK VIII gauge. AS I mentioned, I sprayed the gauge housing black. Made some graphics to attach:

 

Drawing1.jpg

 

A little paint and  put it all together:

 

20230118-214629.jpg

 

Not much more left to make?? Think I have a few electrical switches to do and that's about it. Panel soon.

 

Enjoy

Edited by alzictorini
  • Like 8
Link to comment
Share on other sites

10 hours ago, alzictorini said:

Evening BM's

 

Just finished the MK VIII gauge. AS I mentioned, I sprayed the gauge housing black. Made some graphics to attach:

 

Drawing1.jpg

 

A little paint and  put it all together:

 

20230118-214629.jpg

 

Not much more left to make?? Think I have a few electrical switches to do and that's about it. Panel soon.

 

Enjoy

 

I’m looking forward to seeing all your flight instruments in a panel.

 

Harold

Edited by Sergeant
Link to comment
Share on other sites

Evening BM's

 

Just some minor bits now I noticed I am missing. Switches!  I need a few single type 543s and a twin switch for the compass 5C/993.

 

993.jpg

 

Fresh from the 3D printer:

 

20230120-173405.jpg

 

20230120-173339.jpg

 

Ill make some casts from them in the morning.

 

Enjoy

  • Like 8
Link to comment
Share on other sites

Evening BM's

 

This week I made a dimmer switch type E, 5C/724. I have just about all the dimmer switch types (real items) which I have come across over the years from Lincolnshire markets (bomber county).

It was a simple cast copy I made in the usual way.  Here's a few replica dimmer switches Ive cast from black resin. The front 2 items are my copies and the rear item is a real dimmer switch:

 

20230127-164039.jpg

 

I'm at the point where I need to start looking at cutting out the panel:

 

20230121-102156.jpg

 

With the basic shape drawn out I checked the locats for all the parts (made so far):

 

20230121-113302.jpg

 

With a basic shape drawn I cut out the panel from whit MDF (3mm):

 

20230127-163243.jpg

 

With the parts in place, I can look at making all the labels and warning signs!! There are lots - best get designing.

 

Enjoy

 

 

  • Like 11
Link to comment
Share on other sites

Good evening, Carl. Is the 3mm MDF the finished panel material (substrate) or the pattern for the panel? If it is the finished panel, will you need something behind it as backing material to give it strength?

 

Harold
 

Edited by Sergeant
Link to comment
Share on other sites

Morning BM's

 

That 3mm (currently white) MDF cutout will eventually become the finished item. As its a prototype Ill also use it to draw a master drawing from before final assembly and completion (save for another day).

What I usually do is mount the finished panel on a 6 or 10mm MDF backing board (depending on how big the final frame is going to be - weight). This backing board becomes the back of the picture frame. I print off spacers which I place between the panel and said board. They contain threads which will take screw/bolts from the panel face and the back board. It becomes rigid! It is part of the back board as such when attached and that back board I frame. For example:

 

Heres the panel on a board being readied for mounting/framing. You should see x1 attaching spacer to the left (white). I paint them the same colour as the backing board or the panel before completion:

 

20210826-133246.jpg

 

20210826-133250.jpg

 

This also lifts the panel off the board by about 10mm, gives it a nice little gap which compliments the backdrop, for example:

 

20210908-083036.jpg

 

Because my instruments have no backs and the panel is only 10mm from the back board frame, the final framed item is thin and is perfect for wall mounting:

 

20220621-105747.jpg

 

FYQh-PRQWIAEFBuo.jpg

 

Hope this makes sense?

 

Enjoy

Edited by alzictorini
  • Like 10
Link to comment
Share on other sites

Evening BMs

 

Just looking at the parts for the panel and noticed I dont have a clock!!

 

The Manchester drawings show a S Smiths & Son MKII 8 day clock (6A/579) which looks like this:

 

mkii.jpg

 

Ive made lots of these in the past and I still had 3 of the main components in my spares drawer. I was missing a face and so 3D printed one off in 15mins:

 

20230202-174400.jpg

 

I also had some graphics Id printed off some time ago which I attached to the face:

 

20230202-174615.jpg

 

20230202-182704.jpg

 

Once stuck to the face I painted the numbers with dayglo paint so it glows in the dark like radium (this is not radium!! Its kids paint).

 

I looked in my spares box and found some appropriate hands Id made previously:

 

20230202-191141.jpg

 

These I assembled, sprayed white and added dayglow in the hand centres:

 

20230202-201840.jpg

 

A quick fitment check showed it went together with ease (time being as always, 08:15).

 

20230202-214842.jpg

 

20230202-201902.jpg

 

I now need some glass for the front bezel. As this glass sits proud of the rim I need something about 6mm thick. Ill see whats lying around in the shed - laters.........

 

 

 

Edited by alzictorini
  • Like 6
Link to comment
Share on other sites

A quick look round the shed turned up some 7mm green tint perspex (I think I used it for shelving in a display cabinet). Its a bit scratched and dirty but it will clean up well:

 

20230202-202239.jpg

 

I cut out the rough shape on my bandsaw:

 

20230202-202858.jpg

 

Its now the long process of sanding it circular and to the correct size so as to click into the clock bezel??:

 

20230202-205208.jpg

 

20 mins later, top fit:

 

20230202-205715.jpg

 

Now back into the sander to give it a bevel of plus 45 degrees, 5 mins later:

 

20230202-210255.jpg

 

Now onto the polisher:

 

20230202-210943.jpg

 

This gets rid of all the scratches and makes it look smooth:

 

20230202-210938.jpg

 

Time for final assembly at this point. The body is glued together and the bezel is attached by 3 tiny brass screws, tiny:

 

20230202-213851.jpg

 

It looks spanking:

 

20230202-214559.jpg

 

Glow in the dark check shows this:

 

20230202-214727.jpg

 

In a stand:

 

20230202-224840.jpg

 

20230202-224847.jpg

 

20230202-224900.jpg

 

 

Hope you picked up some tips

 

Enjoy

Edited by alzictorini
  • Like 10
  • Thanks 1
Link to comment
Share on other sites

Nice work Carl. I like the green tinted lens. Who is responsible for making sure the clock is wound and synchronized with the pilot and navigators watches?

 

Harold

 

 

Edited by Sergeant
  • Haha 1
Link to comment
Share on other sites

Evening BM's

 

Name plates

 

WWII RAF Aircraft especially British bombers had little name plates for all the important items in the cockpit. The Manchester was no exception having about 25 plates for a number of items. these are what I've concentrated on this weekend. Some of them have been difficult to decipher as pics are not clear and they are not exactly the same as similar plates used in the later Lancaster.

 

All these plates I designed in fusion and printed off over the last 2 days. Some of them I changed as the font seems slightly bigger in the Manchester than the Lancaster items. 

 

360bits.jpg

 

These printed on my creality like so:

 

20230127-184258.jpg

 

These are some of them and the one in the centre is post clean up and paint:

 

20230205-201353.jpg

 

They fit in between the gauges and switches and give the pilot an idea of whats what, for example:

 

20230205-192108.jpg

 

20230205-192431.jpg

 

20230205-192453.jpg

 

20230205-192519.jpg

 

Ill concentrate on the plates next before cutting out and painting the panel before final assembly:

 

20230205-192405.jpg

 

Have a good one.

 

  • Like 10
Link to comment
Share on other sites

On 2/2/2023 at 10:28 PM, alzictorini said:

It looks spanking:

It certainly does. I love that framed Spitfire Instrument panel too.

 

On 2/3/2023 at 12:50 AM, Sergeant said:

Who is responsible for making sure the clock is wound

Should be the instrument fitter on the before flight inspection. He'd also make sure the instruments were clean and lights working.

  • Like 3
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...