Seahawk Posted April 3, 2022 Share Posted April 3, 2022 6 hours ago, Mycapt65 said: the secret to my non success is Mr.Color thinner. It removes paint with out destroying plastic or glue joints. Is that just acrylics or acrylics and enamels? Link to comment Share on other sites More sharing options...
Mycapt65 Posted April 3, 2022 Share Posted April 3, 2022 I never tried it on water based acrylics. It will remove laquers and enamels safely. Some water based acrylics can be removed with ammonia. 1 Link to comment Share on other sites More sharing options...
EC182 Posted April 4, 2022 Author Share Posted April 4, 2022 (edited) I lightly sanded everything down and went at it with the Mr. Paint Remover, using cotton buds and makeup pads. It's good stuff. The paint didn't come off quite as easily as in the video, but come off it did, with a little bit of patience. About 30 minutes was required to strip the upper surface of one wing. As that's all I can generally manage at a time (if even), it'll take a few more days to finish the job. The plastic appears unaffected and restored to its original condition, except that - and this could be my imagination - it now appears to be a shade lighter than it was out of the box. Thankfully, glue and filler seem to be unaffected also. It's a bit difficult to get into the crevices around the wing fences, but I'll tidy those up later on. I'd post a picture, but I don't see an option for it here. Edited April 4, 2022 by EC182 Link to comment Share on other sites More sharing options...
Timo Posted April 4, 2022 Share Posted April 4, 2022 Hi there, I'd definitely strip the paint and start again. I like making model airliners, so whenever an airline introduces a new livery (which is quite often nowadays) I'll strip-off the old livery and repaint rather than buy another model. I currently use Revell Paint Remover which does an excellent job. Only thing to watch is that the fluid tends to creep under making tape so, if you need to protect any of the existing paint or sensitive areas like your cockpit, its best to position masking tape with a bit of a margin and then (after stripping) sand away the unwanted paint in this boundary area. It works for me, so it has to be simple!! Best of luck Tim Link to comment Share on other sites More sharing options...
EC182 Posted April 5, 2022 Author Share Posted April 5, 2022 16 hours ago, Timo said: Hi there, I'd definitely strip the paint and start again. I like making model airliners, so whenever an airline introduces a new livery (which is quite often nowadays) I'll strip-off the old livery and repaint rather than buy another model. I currently use Revell Paint Remover which does an excellent job. Only thing to watch is that the fluid tends to creep under making tape so, if you need to protect any of the existing paint or sensitive areas like your cockpit, its best to position masking tape with a bit of a margin and then (after stripping) sand away the unwanted paint in this boundary area. It works for me, so it has to be simple!! Best of luck Tim How do you apply the Revell Paint Remover? Link to comment Share on other sites More sharing options...
Paul J Posted April 5, 2022 Share Posted April 5, 2022 If it's just acylic paints, the stuff that Hannants do called Purisol and comes in small or large bottles works well without harming plastic. Also it makes a good paint thinner for acrylics. Just as an aside, on purely resin kits, I successfully used cellulose thinners to strip paint off. Again, no harm to the model. Link to comment Share on other sites More sharing options...
Timo Posted April 5, 2022 Share Posted April 5, 2022 3 hours ago, EC182 said: How do you apply the Revell Paint Remover? Hi mate, Revell Paint Remover - you just brush it on and after a few minutes the paint reacts and starts to crinkle and lift. I then use an old toothbrush to remove the paint especially from panel lines, aided by a small plastic scraper to help lift any stubborn paint. It doesn't affect the plastic and leaves a nice clean surface just like when you first built the kit. Just note my warning about fluid creep under masking tape - if you are trying to preserve some of the existing paintwork, leave a good margin when masking. Hope this helps, Tim Link to comment Share on other sites More sharing options...
EC182 Posted April 8, 2022 Author Share Posted April 8, 2022 Cheers Tim, appreciate it. I finished the job with Mr Paint Remover and am very happy with the result. A bit of primer and some black basing and it'll be good to go again Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now