Jump to content

BQM-34A (Q-2C) Firebee (48403) 1:48 ICM


Julien

Recommended Posts

BQM-34A (Q-2C) Firebee (48403)

1:48 ICM

 

spacer.png

 

People think drones are a new thing for the military but in reality they are not. The Firebee was developed by Ryan for the new USAF in 1948 as a jet powered gunnery target with the first flight being in 1951. The USAF Designation was Q-2A, and when the US Navy bought them they designated them KDA-1. The original Firebees were air launched from a modified A-26, or ground launched using a RATO system. The system was later used by the US Army as well. Q-2Bs were fitted with a modified engine for higher altitudes. They were developed over time with the KDA-4 being the main USN version, however differences were mainly internal. The Royal Canadian Air Force purchased 30 KDA-4s which were launched from an Avro Lancaster Mk.10DC.  

 

In the late 1950s the USAF Awarded Ryan a contract for a new second generation Firebee this would become the BQM-34A or Q-2C. This was a bigger airframe with longer wings. One of the main recongition features was the fact the original nose intake was replaced by a chin intake for the new Continental J69-T-29A turbojet. As well as the USAF and USN the US Army had a ground launched (With Rocket assist) designated the  MQM-34D, this version having a longer wing than the USAF & USSN ones. The main launch aircraft for these new drones was the DC-130. While initial production ended in 1982 the production line was re-opened in 1989 to  produce more targets. These BQM-34S featured improved avionics and a new J85-GE-100 engine.

 

 

The Kit

This kit is a brand new tool from ICM, following on from their original kit. This boxing gives two drones but without trailers no doubt designed to be hung under one of their Invader kits at some point ;)  The kit arrives on one sprue for each Drone (shown once).  The model will be just over 145mm long when built. 

 

spacer.png

 

Construction is fairly basic and starts with the full length intake/exhaust for the engine.  The engine is installed inside the main body and it can be closed up, a triangular inert goes in the top.  The left and right main wings are single parts, these have tabs on them for where they join inside the main body to lock together. The tail planes are also single part with tabs again to lock in place. single piece. End plates are added to the tail planes and the rudder goes on the top. 

 

 

Decals

Four options are provided for on the decal sheet (but as you get two drones you get two decal sheets)

 

  1. USN BMQ-34, Naval Base Ventura County (overall red)
  2. USN BMQ-34, 36 Mission markings. (Red with Yellow wingtips and a checker board tail)
  3. USAF BQM-34, Wallace Air Station. (Red with Yellow wingtips as on the box art)
  4. USN BQM-34, circa 2000s in overall white. 

 

spacer.png

 

spacer.png

 

The decals look nicely printed, in register with no issues.

 

Conclusion

This is a good looking kit which will look good hanging under a model, or built as a standalone model. Highly recommended. 

 

Available in the UK from importers H G Hannants Ltd.
bin.jpg


Review sample courtesy of
logo.gif

  • Like 1
Link to comment
Share on other sites

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...