Julien Posted August 26, 2021 Share Posted August 26, 2021 Mirage IIICJ (72062) 1:72 ModelSvit Sacré bleu! If you have not heard of the Mirage III where have you been? The Mirage III is one of the most recognisable aircraft to emerge from the Dassault Aviation stable in post war France. The Mirage III grew out of French government studies for a light weight all weather interceptor able to reach 18,000 meter in altitude in Six minutes and able to reach mach 1.3 in level flight. The tail less delta combined the wing with an area ruled fuselage to achieve its speed. The Mirage IIIC would remain in French service from 1961 until 1988. The largest export customer for the Mirage III was Israel. This version being the Mirage IIICJ. Israel found these aircraft more than a match for anything her neighbours we able to field with the aircraft being a success in combat with Syrian, Jordanian and Egyptian aircraft. Israel then sold some of these aircraft to Argentina. Kit This is the eagerly awaited new kit from Modelsvit. The kit resembles a high quality shorter run kit with fine surface details. While the parts resemble some more main stream manufactures in appearance they will no doubt need more care in the assembly. In the box we get 7 sprues of grey plastic, a clear sprue, a PE fret, masks(not shown) , and a decal sheet.. Construction starts in the conventional way with the cockpit. The seat is built up from 7 parts with PE belts and handles. The tub is made up from the base, rear bulkhead, two sidewalls and the area behind the cockpit. The instrument panel with its PE faces goes in, and PE is supplied for the side consoles. The cockpit then goes into the fuselage. The coaming then goes on in front of the instrument panel. Next up the engine exhaust is made up. This is a three part tube with the engine end and burner ring at the front and the inner nozzle at the rear. Once the engine and cockpit are in the fuselage can be closed up. Construction then moves onto the wing, first up the wheel wells need to be fully boxed in. Holes need to be opened up for the underwing stores. The main fuselage can then be joined to the lower wing with the upper wings following as well as the vertical fin. At the rear of the main wing the separate flaps and flap tracks are fitted. Here there are parts for dropped or straight flaps. The intakes are then fitted to the main fuselage, and at the rear underside the ventral strake is fitted. Moving on to the landing gear, the legs are made up and the main wheels can be fitted to their gear legs, and these can be fitted, along with the noise wheel at the front. For under wing/fuselage stores a single Matra R530, 2 Shafrir-2, 2 AIM-9D sidewinders, 2 RP-62 1300L tanks, and 2 RP-18R 500L tanks are supplied. These and the appropriate pylons can be fitted. Finishing touches are fitting the gear doors, canopy (both a one part closed, and multi part open options are provided), lastly some aerials (where appropriate). Decals There are 5 schemes provided in the kit; the decals are well printed by Decograf with no obvious flaws. From the box you can build; Mirage IIICJ No. 103, 253 Sqn, Eitham Air Base, Israel 1981 (2 tone grey scheme) Mirage IIICJ No. 758, 101 Sqn, Harzor Air Base, Israel, 1974 (Brown, Green, Tan scheme) Mirage IIICJ No. 107, 117 Sqnm Ramat David Air Base, Israel, 1973 (Brown, Green, Tan scheme with large yellow recognition markings) Mirage IIICJ No. 159, Argentinian Air Force, seen at the IAF Museum 2004 (Green, Blue Scheme) Mirage IIICJ No. C-704 Argentinian Air Force, Base Aerea de Rio Gallegous, 1986 (Dark Earth, Sand scheme) Conclusion It is good to see a decent model of the Mirage IICJ available in 1.72, this should build up to make an eye catching model if care is taken with the build. Highly recommended. Review sample courtesy of 10 2 Link to comment Share on other sites More sharing options...
Antoine Posted August 26, 2021 Share Posted August 26, 2021 2 hours ago, Julien said: Sacré bleu! Obviously, you've not been in France since quite some time... Say, two or three centuries ago? 1 3 Link to comment Share on other sites More sharing options...
drake122 Posted August 26, 2021 Share Posted August 26, 2021 @ModelSvit Balkans Mirage 5 next, pretty please?😁 I built the EA/EBR boxing, a lovely kit that one as well. Link to comment Share on other sites More sharing options...
Fukuryu Posted August 28, 2021 Share Posted August 28, 2021 (edited) Good to see that 117 Sqn. badges are included in the decal sheet, since there is no reference to them on the illustrated profiles; that would allow to make an accurate "107" from the 1976-79 time frame. Edited August 29, 2021 by Fukuryu Link to comment Share on other sites More sharing options...
manuel Posted August 29, 2021 Share Posted August 29, 2021 Caution this is not the initial Mirage IIICJ with Atar engine but the upgraded with F-4 engine, a total new look mirage. Link to comment Share on other sites More sharing options...
SPAD64 Posted August 29, 2021 Share Posted August 29, 2021 37 minutes ago, manuel said: Caution this is not the initial Mirage IIICJ with Atar engine but the upgraded with F-4 engine, a total new look mirage. Wrong, the model is correct , Mirage IIICJ have been updated with an atar 9c (engine of the Mirage IIIE slightly powerful). Link to comment Share on other sites More sharing options...
Hook Posted August 29, 2021 Share Posted August 29, 2021 3 hours ago, manuel said: Caution this is not the initial Mirage IIICJ with Atar engine but the upgraded with F-4 engine, a total new look mirage. Methinks you mean the Kfir - that was a Mirage 5 (not this IIICJ version) re-engined with a J79. @Julien Nice review, most tempting. Cheers, Andre Link to comment Share on other sites More sharing options...
Fukuryu Posted August 29, 2021 Share Posted August 29, 2021 12 hours ago, manuel said: Caution this is not the initial Mirage IIICJ with Atar engine but the upgraded with F-4 engine, a total new look mirage. It is a Mirage IIICJ with an Atar engine, just upgraded to an Atar 9C (same as the Nesher) instead of the original 9B. You can build an earlier Atar 9B-engined Shahak from the previous Mirage IIIC boxing that even included Israeli markings. Link to comment Share on other sites More sharing options...
Fukuryu Posted August 29, 2021 Share Posted August 29, 2021 11 hours ago, SPAD64 said: Wrong, the model is correct , Mirage IIICJ have been updated with an atar 9c (engine of the Mirage IIIE slightly powerful). Atar 9B and 9C had more or less the same power, but 9C has an improved afterburner, shorter and with 18 "petals" instead of the two clamshells of the 9B version. This account for the main visual difference between the original and re-engined Shahaks. 1 Link to comment Share on other sites More sharing options...
manuel Posted August 31, 2021 Share Posted August 31, 2021 On 29/08/2021 at 22:42, Fukuryu said: Atar 9B and 9C had more or less the same power, but 9C has an improved afterburner, shorter and with 18 "petals" instead of the two clamshells of the 9B version. This account for the main visual difference between the original and re-engined Shahaks. Helas it changes a lot the rear part, with the parachute container pointing up. For me the tittle of the kit should have been "upgraded Mirage IIICJ" it was less confusing. 1 Link to comment Share on other sites More sharing options...
Fukuryu Posted August 31, 2021 Share Posted August 31, 2021 29 minutes ago, manuel said: Helas it changes a lot the rear part, with the parachute container pointing up. For me the tittle of the kit should have been "upgraded Mirage IIICJ" it was less confusing. @manuel, if you compare them carefully you'll see that the parachute container is in the same position in both; the shorter rear end of the 9C is what make it look that way. Couldn't agree with you more on the name, though; all Israeli Mirages were CJs, regardless of engine or any other modification. Link to comment Share on other sites More sharing options...
manuel Posted September 1, 2021 Share Posted September 1, 2021 (edited) 15 hours ago, Fukuryu said: @manuel, if you compare them carefully you'll see that the parachute container is in the same position in both; the shorter rear end of the 9C is what make it look that way. Couldn't agree with you more on the name, though; all Israeli Mirages were CJs, regardless of engine or any other modification. if you compare this two pictures https://www.escadrilles.org/wp-content/uploads/2011/01/Mirage3C_1977_10-RH.jpg and https://www.airliners.net/photo/Argentina-Air-Force/Dassault-Mirage-IIICJ/1888197/L you will see the parachute housing aren't the same. For the tittle it's ok for Israel it's the same BUT in the box for modelers Modelsvit could have indicate there is no the same. Manuel Edited September 1, 2021 by Julien no copyrighted photos 1 Link to comment Share on other sites More sharing options...
drake122 Posted December 19, 2021 Share Posted December 19, 2021 On 8/29/2021 at 10:30 PM, Fukuryu said: It is a Mirage IIICJ with an Atar engine, just upgraded to an Atar 9C (same as the Nesher) instead of the original 9B. You can build an earlier Atar 9B-engined Shahak from the previous Mirage IIIC boxing that even included Israeli markings. I am currently looking at aftermarket resin engines for this kit, and based on this information, I have concluded, that ResKit make 2 separate engines - one labeled for 'Mirage 3E' and one for 'Mirage 3C'. I believe the 3E engine variant is ATAR 9c usable for more than one Modelsvit kit (the original 3E boxing, the EA/EBR boxing and this 3CJ boxing as well). The 3C variant is ATAR 9b and only usable for Modelsvits Mirage 3C boxing. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now