Mike Posted June 30, 2021 Share Posted June 30, 2021 Marder I on FCM 36 Base (35339) 1:35 ICM via Hannants The Marder series of Tank Destroyers were originally created to fill a need for mobile artillery that could be self-sufficient and yet work in unison with troops and tanks at the high speed of Blitzkrieg. The concept was to mount a PaK40 or captured Soviet 76 mm F-22 Model 1936 divisional field gun on a captured tank chassis that had been stripped of its superstructure and given an extended splinter shield around the gun and its crew, whilst leaving the roof open to the elements. Many of the initial Marder Is were built on French Lorraine or Czech 38(t) chassis, but a small number were constructed on the obsolete FCM 36, with a large shield that extended almost the whole length of the vehicle. FCM stands for Forges et Chantiers de la Méditerranée, who were based at Toulon in the French Riviera. They saw use on the Eastern Front initially, then also in the West after D-Day. Although they were intended to be mobile artillery that was capable of destroying most tanks at a respectable range, they were only lightly armoured to protect their crews from shrapnel, shell splinters or light arms fire from all-round, which is somewhat better than a standard artillery piece would afford its crew, although the open roof would make a tempting target for grenades or demolition packs in close combat. It would have been uncomfortable for the crew in bad weather too, necessitating a temporary tarpaulin roof to keep the precipitation out, but very little of the cold. The Kit This is a substantial re-tool of ICM’s previous FCM 36 kits, adding the specialised parts for the conversion undertaken by Baustokommando Becker at the time. It arrives in a standard ICM top-opening box with additional captive inner lid, with seven sprues in grey styrene, two flexible black sprues of track links, a decal sheet and glossy instruction booklet with colour profiles in the back pages for painting and markings. The original FCM 36 kit was only released in 2020, so it’s a modern tooling with plenty of detail and this boxing includes the majority of the interior due to the open roof. Construction begins with the lower hull, which is made up initially of the floor and two sides, with bulkheads added to the sides to support the lower sponson panels that give the vehicle more ground clearance. The running gear is made up from a three-part drive sprocket, eighteen sets of twin wheels that are fitted to eight double bogies and two singles, then the big idler wheels at the rear of the hull on sliding tensioning axles. The sloped armoured upper sponsons are installed along the way, with the mud-shedding apertures on each side. Two pairs of return rollers on the top run are glued inside the sponson, then the flexible black “rubberband” tracks are glued together, the instructions neglecting to mention that styrene glues won’t join them, so you should use super glue or epoxy instead. Each run has two sections, with the joints best placed in the centre of each run so they stand less chance of being seen on the finished model. Detail on the tracks is very nice, with twin guide horns and perforated centres like the real thing, but of course the links will curve round the ends, rather than give the correct faceted look that individual links provide. The upper hull is a new part, and has an opening at the front where the turret would have been, and has the two fender sides fitted to the rear before it is joined to the lower hull, hiding most of the upper track run. At the rear a large louvered panel and fixtures on the final-drive access hatches are glued on first, with the two exhausts and their mufflers slotted into grooves to their side, and a C-shaped manifold joining them at the top. Pioneer tools and towing eyes are the final parts for now, because the gun must be made up first. The PaK40 is begun by making up the cradle and inserting the breech, then the one-piece gun tube and part of the elevation mechanism. The cradle trunnions are held in place by the side frames, which are fixed to the arrow-shaped floor. More of the elevation mechanism is added, then the floor is mated to the hull, covering up the turret aperture, then having armoured supports slipped under the overhang. The gun’s double-layer splinter shield is slid over the barrel and glued to the gun, then the two faceted side panels are fitted out with shell racks, then attached to the side of the vehicle, to be joined by the rear wall after adding some stowage boxes inside and a pair of louvered panels to the sides. Twenty-eight shells are supplied on the sprues to be slotted into the holes in the racks nose down, then some spare tracks are fixed to the sides, and the self-defence MG34 machine gun is fitted to the front shield on a short pintle-mount. An outer splinter shield slides over the gun, and then you can put on the two-part muzzle brake, which gives the impression of a hollow barrel. Markings There are three markings options on the decal sheet, with a nice variation between them, all of which saw action (or training exercises) in 1943. From the box you can build one of the following: 931st Assault Gun Division, 2nd Battery, France, 1943 Training camp of the Mobile Brigade “West”, summer 1943 Mobile Brigade “West” 2nd Battery, Manoeuvres, Spring 1943 The decals are printed by ICM’s usual partner, which is a guarantee of good registration, sharpness and colour density, with a thin gloss carrier film cut close to the printed areas. Unusually for a model review, we’re going to talk about actual paint. That’s because ICM have just recently announced that they are launching their own range of paints, beginning with a set of 6 pots for this particular model, with another set for their Cobra helicopter kit in 1:32. The rest of the range will be following along in due course, totalling 77 in all. If you’d like to know more, follow the link at the end of the review (I’ll add it later). Conclusion Another peculiar, interesting example of German re-use of captured vehicles, and a nicely detailed one too. Now you can also paint your model with ICM paints, which is novel. Highly recommended. Available in the UK from importers H G Hannants Ltd. Review sample courtesy of 2 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now