Julien Posted November 27, 2020 Share Posted November 27, 2020 MiG-25RU Soviet Training Aircraft (72176) 1:72 ICM In the early part of the Cold War, the strategic bomber was seen as the obvious means by which to deliver a nuclear payload. The interceptor - large, heavy and fast - was seen as the equally obvious countermeasure. The MiG-25 Foxbat was, in many ways, the ultimate embodiment of this technology. It wasn't particularly groundbreaking and nor was it particularly sophisticated, but it was capable of incredible speed and could carry four large missiles to high altitudes very quickly indeed. The MiG-25's shortcomings as a combat aircraft were largely addressed through the MiG-31 Foxhound, but the type continued as an effective mission platform in a variety of guises. The RU version being the twin seat trainer for the reconnaissance version of the Foxbat. The Kit This kit is now the fifth iteration of ICM's new 1/72 MiG-25 family, following on from the other variants. The model is pretty much a scaled down version of their 1:48 kit, which is a jolly good thing indeed. Inside the robust top-opening box are seven frames of light grey plastic and one of clear plastic. The kit is almost identical to the previous iterations, but includes revised parts for the nose. The airframe is covered in crisp, recessed panel lines which look very good indeed, and the mouldings are crisp and clean. The instructions are an A4 stapled booklet which has been printed in colour and the decal sheet is clear and well printed. The overall impression is of a well-executed, modern kit which looks like it should be thoroughly enjoyable to build. Construction begins with the rear cockpit and nose gear bay. Some detail is moulded in place on the sidewalls of the cockpit, with extra parts provided to represent additional details. Before the main structure of the cockpit can be completed, however, you have to add the bulkhead that forms the front wall of the cockpit and the rear wall of the nose gear bay. The instructions have you installing the nose gear leg at this stage, but I can't see any logical reason as to why this can't be done at the end. This would, of course, save you from breaking the leg part way through the build. The cockpit itself is nicely detailed, with the ejector seat alone made up of no fewer than five parts. An instrument panel and control column completes this section. Once the forward fuselage halves have been joined together, the whole sub-assembly fits onto a spar that also holds the huge engine air intakes. I've noticed that kit manufacturers are moving increasingly toward this style of construction, where certain parts are provided for purely structural purposes instead of the older slot and tab style of construction. I guess the main advantage, other than strength, is that everything can be positioned at exactly the right angle - a helpful feature for kits that feature quit a complex breakdown of parts such as this one. Each engine intake is full-length, with engine compressor faces provided. What results is a complete forward section of the aircraft up to the wing roots, with the internal structure of the air intakes protruding from the rear. The lower face of the main fuselage can be joined to this structure once the main landing gear bays have been added. ICM suggest that you add the main landing gear legs at this stage. Again, I can't see any reason why they couldn't be fettled into place after the main construction has been completed. Once the lower face of the main fuselage is in place, another structural bulkhead can be added, after which the slab-sides of the fuselage, including the outer faces of the air intakes, can be added. The dustbin-like jet exhausts are added at this stage, and very nicely detailed they are too. Once in place, the upper face of the fuselage can be added. Some modellers have noticed that the central spine has a flattened profile instead of a rounded shape. This is true, but I imagine most modellers will choose to live with this flaw. All that remains now is to add the nosecone, flying surfaces and finishing details. Each vertical tail is split vertically, with a seperate rudder. The outer face is moulded with part of the rear fuselage in place, so presumably it will be impossible to fit these parts at the wrong angle. Somewhat surprisingly, the upper wings are not moulded in one part with the upper fuselage. Instead, they are split into separate port and starboard halves, with two separate flaperons and upper wing fences and fittings. The nosecone is simply split vertically and houses the front cockpit. This is made up and added in along with its rear bulkhead, Once closed up the completed nose section can be joined with the rest of the fuselage. The canopies are nice and clear and can be finished in either open or closed position. Even though the wing tip missile rails are present no armament was used, and plugs are provided for the underwing pylon spaces as well. Other than that, and a few aerials, lumps and bumps, the huge aircraft is now finished. Decals Two options are provided for on the decal sheet: MiG-25RU, 47th HRAP, Russian Air Force 2001 MiG-25RU, No. 102 Sqn Indian Air Force, 1990 The decals look nicely printed and a full set of stencils is included. Conclusion We've waited a while for a new, more more modern kit of the Foxbat in this scale, but the wait has been worth it. ICM's effort is excellent, with high quality mouldings and plenty of detail. Overall this is a well executed and carefully designed kit, while the trainer configuration is very appealing indeed. Highly recommended. Available in the UK from importers H G Hannants Ltd. Review sample courtesy of 4 3 Link to comment Share on other sites More sharing options...
aircooled Posted November 27, 2020 Share Posted November 27, 2020 Very nice review! Has this already been released in 1/48? Did I miss it or is the 1/72 first? 1 Link to comment Share on other sites More sharing options...
Julien Posted November 27, 2020 Author Share Posted November 27, 2020 2 hours ago, aircooled said: Very nice review! Has this already been released in 1/48? Did I miss it or is the 1/72 first? They have not done this one in 1.48 yet. Link to comment Share on other sites More sharing options...
tomthounaojam Posted November 29, 2020 Share Posted November 29, 2020 I am buying myself a one, Thanks boss for the sprue shots and review. Link to comment Share on other sites More sharing options...
James G Posted February 1, 2021 Share Posted February 1, 2021 I have the RBT version, it's a superb kit. One little gripe would be that ICM's decals are not much to write home about... perfect excuse to get some aftermarket ones! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now