wellsprop Posted September 24, 2020 Share Posted September 24, 2020 Hi all, Since summer abruptly ended this Monday gone, I have had significant problems with my Anycubic Photon printer, multiple failed prints despite having no issues previously. I cleaned, reset and aligned everything, but to no avail, therefore the cold weather must be to blame. My printer is out in my garage, which has been very hot throughout the summer 20-30 degrees easily and retains the heat overnight. Since it's got cold, it's been going down below 10 degrees, which has led to multiple failed prints. Here's my solution https://www.amazon.co.uk/AIICIOO-Reptile-Heat-Warmer-Thermostat/dp/B083HTFVDF/ref=sr_1_5?adgrpid=100884513262&dchild=1&gclid=CjwKCAjwwab7BRBAEiwAapqpTOhzyrXTcQxyahJ8LyA9W5HN_8KAxhcYfkV25tYn6gcyf4oe6cESIBoCa-AQAvD_BwE&hvadid=445889290454&hvdev=c&hvlocphy=9045663&hvnetw=g&hvqmt=e&hvrand=9376490572805432887&hvtargid=kwd-300346743099&hydadcr=7168_1741700&keywords=heat+pad+with+thermostat&qid=1600779227&sr=8-5&tag=googhydr-21 I bought the above reptile heater mat with thermostat from amazon for £35 and slid the mat around the back of the z axis and taped the thermostat to the inside of the printer. I cut a small slot into the door through which the cables exit. I set the thermostat to 28 degrees and put the upturned box (in which the printer arrived) over the top of the printer. Results? No failed prints last night (it was even chillier last night too!). Cheers Ben 1 2 Link to comment Share on other sites More sharing options...
JeffreyK Posted September 25, 2020 Share Posted September 25, 2020 Very good! I'll keep this in mind and my replicate it when needed. Cheers, J Link to comment Share on other sites More sharing options...
Andy Moore Posted September 25, 2020 Share Posted September 25, 2020 Interesting solution. I'll have to try this with my Mars. The resin I'm using has a recommended operating temp of 20-25 degrees and the room the printer is in falls way below that in winter. Andy Link to comment Share on other sites More sharing options...
Kushan_Farsight Posted September 25, 2020 Share Posted September 25, 2020 interesting to see thermal levels affect resin printers so strongly. Almost appears as temperamental to temperature changes as printing in ABS! good to know. Link to comment Share on other sites More sharing options...
wellsprop Posted September 25, 2020 Author Share Posted September 25, 2020 The change in the viscosity of the resin is very noticeable, it's much less viscous at higher temperatures, hence it flows and prints better. Link to comment Share on other sites More sharing options...
bootneck Posted September 25, 2020 Share Posted September 25, 2020 Thanks Ben, I shall probably invest in one of those; however, I will look into laying it flat and building an aperture around it, with the printer raised a cm or so above it. cheers, Mike Link to comment Share on other sites More sharing options...
wellsprop Posted September 25, 2020 Author Share Posted September 25, 2020 2 hours ago, bootneck said: Thanks Ben, I shall probably invest in one of those; however, I will look into laying it flat and building an aperture around it, with the printer raised a cm or so above it. cheers, Mike That's what I did at first, with the box placed over the top. I found it didn't hold heat so well. It would probably be worth creating some sort of well insulated box to put over the whole thing if you go down that route. 1 Link to comment Share on other sites More sharing options...
Bozothenutter Posted September 26, 2020 Share Posted September 26, 2020 Great idea! Link to comment Share on other sites More sharing options...
wellsprop Posted November 28, 2020 Author Share Posted November 28, 2020 Bit of an update, in the last couple weeks it has got VERY cold here, dropping below freezing overnight (the garage must go down to just above freezing). I've had to put the plastic bag that the printer came in over the printer, before putting the box over the top to make sure it's insulated enough - it stays at a toasty 28 degrees c. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now