Xirurg Posted July 10, 2020 Share Posted July 10, 2020 Hi All I'm having issue with Vallejo Model Air when using masks. There is visible "step" between two colors where the edge of the mask was Here is the picture: I'm using Vallejo Model Air, spraying at 15-18 PSI, straight from the bottle, Tamiya masking tape. I've used Vallejo on 3 models and got this "step" issue on 2 of them. The only difference was the paint - the one where I didn't get step was IJN Dark Green (AV71310) and Aluminium (AV71062). Picture above uses Dark Earth (AV71323) and Dark Green (AV71324). That makes me wonder it's gotta be a paint issue - maybe some of the paints are thicker? Maybe I didn't mix it enough? Any advice would be greatly appreciated. Link to comment Share on other sites More sharing options...
busnproplinerfan Posted July 10, 2020 Share Posted July 10, 2020 I'm curious to, I haven't used Vallejo yet but want to so I'll watch this. This would loose a point in a contest for sure. Link to comment Share on other sites More sharing options...
Mark Harmsworth Posted July 10, 2020 Share Posted July 10, 2020 I can't comment on Vallejo Model Air paint but, when using masks, you need to spray away from the mask otherwise, if you spray towards the mask, a ridge of paint can build up. It's possible that's what's happened rather than being a paint brand problem. Mark 1 Link to comment Share on other sites More sharing options...
ckw Posted July 10, 2020 Share Posted July 10, 2020 10 minutes ago, Mark Harmsworth said: if you spray towards the mask, a ridge of paint can build up exactly, and to be honest it can be tricky to avoid when spraying at odd angles - inevitably you'll end up spraying against some edge! When the paint is truly hard, you can use very fine grade paper (e.g. 5000) to very carefully sand down the ridge. It will change the lustre of the paint, but you can fix that with whatever top coat (varnish, Klear) you use. You can minimise the chances of it occuring by using an ultrathin masking media (when I really need a hard edge, I use parafilm) You can avoid it by using the blu-tak sausage technique (which can still produce quite a hard edge if that's what you want. Cheers Colin Link to comment Share on other sites More sharing options...
Xirurg Posted July 10, 2020 Author Share Posted July 10, 2020 30 minutes ago, Mark Harmsworth said: you need to spray away from the mask Thanks for the reply however I don't think that's the case. I never got such ridges when spraying with Tamiya Acrylic. I'll use blue-tak for masking next time - wanted to try that anyway. I think it'll look better on a model. Link to comment Share on other sites More sharing options...
Steve Noble Posted July 10, 2020 Share Posted July 10, 2020 (edited) If you use masking tape you'll get a hard edge. The more paint you apply, the larger the step. If you use blu-tac the edge will be minimal, because the blu-tac doesn't seal down tightly like tape does. Only way to avoid a step altogether is spray the colours free hand with no masking, but I guess you won't get as neat an edge as with tape. Other solution is to clear coat over the paint job, this will reduce the step significantly. Edited July 10, 2020 by Steve Noble Link to comment Share on other sites More sharing options...
Matthew1974 Posted July 11, 2020 Share Posted July 11, 2020 Also, if I may suggest, you may be spraying the upper coat a little heavy - try thinning the paint a bit and dialing the pressure back a tad. I have never had this problem with Vallejo but I did with enamels, which I was spraying too heavy, seeking total uniformity, but not looking too realistic. I now use paper masks tacked in place with tiny roles of Tamiya tape and have achieved an almost hard edged demarcation between colors, while at the same time allowing for some variation in tone. If sticking with a true hard edged mask, another thing to look at is removing the mask as soon as possible to give the paint a chance to self-level. Hope it helps! Link to comment Share on other sites More sharing options...
Rabbit Leader Posted July 11, 2020 Share Posted July 11, 2020 Although I don’t use Vallejo I would think this issue would be quite common with any paint brand where you’ve allowed too much paint to build up. I constantly get this when applying yellow leading edge ID markings to WW2 RAF fighters. The white undercoat on top of the yellow top coat will invariably be thicker than the Camouflage colours. A quick sand will reduce it, however may also remove the paint as well. Cheers.. Dave Link to comment Share on other sites More sharing options...
lesliegl Posted July 20, 2020 Share Posted July 20, 2020 I've had that problem as well..Vallejo Model Air seems to splatter on rather than mist on like Tamiya or Mr Hobby acrylics.. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now