Jump to content

North American P-51D/K Mustang "8th Air Force" (LS-010) - 1:48 Meng Model via Creative Models


Julien

Recommended Posts

North American P-51D/K Mustang "8th Air Force" (LS-010)

1:48 Meng Model via Creative Models

 

spacer.png

 

Originally developed to fulfil a British requirement for new fighter aircraft, the unmistakable North American P-51 Mustang famously went from drawing board to first flight in just 178 days. It went on to become one of the most famous and successful aircraft of the Second World War.  Transformed by the addition of Rolls Royce’s legendary Merlin engine, the Mustang went from strength to strength and was eventually developed into several variants. The P-51D introduced a number of improvements in response to combat experience, including a cut-down rear fuselage and bubble canopy and an increase in the number of 0.5 inch machine guns from four to six. The P-51K designation was used for Dallas built P-51Ds an Aeroproducts Propeller in place of the usual Hamilton Standard one. However the hollow bladed Aeroproducts unit was found to be unreliable and produced dangerous vibrations at full throttle. These units were replaced by Hamiltons standard units.  Over 8000 P-51Ds were produced, more than any other Mustang variant. 

 

 

The Kit

This new tooled P-51D from Meng is designed as a "snap together" kit and Meng trumpet it can be put together without glue. As such the kit is designed in a different way than your standard kit. There are more tabs and inserts and construction varies from a standard kit. Having spoken to a couple of modellers who have built the kit it certainly does go together without glue, however the modeller it would seem would be wise to glue it as they go. The kit arrives on five sprues of dark grey plastic and a clear sprue. Construction starts its seems in the conventional way with the cockpit. 

 

m02.jpg

 

m03.jpg

 

The front fire wall and instrument coaming are assembled with the rudder pedals clipping it. The radio area behind the pilot is installed onto the cockpit floor. The control column is added and the seat made up, then fitted. Moving on to the fuselage sides, side panels are added, then the tail wheel well & wheel are made up and attached. A couple of insert parts are attached and then the fuselage can be closed up. The propeller is then made up fro two sets of two bladed added to hub. The top engine cowl part is added along with the exhausts (2 different types being provided).

 

m04.jpg

 

m05.jpg

 

Construction then moves onto the wings. The landing gear complete with wheels are added into the gear bay, this is then inserted into the rear wing. The flaps (down position only) are then added into the lower wing, and the whole thing is trapped by the addition of the upper wing. Inserts are provided on the leading edge for the guns. The cowling under the main engine is then added to the fuselage. The main ventral radiator assembly is then made up, the wing installed and then the radiator installed. Next the gear doors are installed (either up or down) and the rear scoop for the radiator added. Underwing stores are made up and installed. There is a choice for 100lb bombs, 75 Gal & 108 Gal drop tanks. Lastly the frame is added inside the canopy and its installed, followed by a top fuselage insert, the tailplanes and the rudder.

m06.jpg

 

 

 

Markings

Two options are provided on a sheet made in house by Meng. 

 

  1. P-51D 44-14789 "Missouri Armada" (as box art)
  2. P-51K 44-11622 "Nooky Booky IV"

 

spacer.png

 

 

Conclusion

Recommended if you want something a bit different, or you would like a project that snaps together, however I wont be replacing any of my other Mustang kits with this one.

 

 

bin.jpg

 

Review sample courtesy of

logo.gif

  • Thanks 2
Link to comment
Share on other sites

Got the original boxing on the bench right now for the P-51 STGB. 

Have to say I'm impressed with it so far.. Yes the snap fit is a bit of a gimmick and you'd still need a dab of glue in places even if you went the snap fit route. 

Treat it like a normal kit and the fit/detail is very nice. 

My only negative is the high retail price compared to the recent P-51 competition from Airfix & Eduard.. Although the Meng kit can be found cheaper if you shop around 

 

I'd recommend it for sure. 

  • Like 3
  • Thanks 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...