Courageous Posted October 4, 2020 Share Posted October 4, 2020 The weathering is enhancing the detail, looking very nice. STANCHIONS! Stuart 1 1 Link to comment Share on other sites More sharing options...
Steve D Posted October 15, 2020 Author Share Posted October 15, 2020 In case anyone wondered, our phone line and internet connection has been down for almost two weeks now, very frustrating and not a little debilitating for the small amount of work I still have to accomplish... Still progress has continued on the SGB. Stanchions are all done and wired up, For those how didn't read the Fairmile thread, I use split pin stanchions from James Lane. These come over length and need to be soldered together and to a base which I've etched. The whole process is repetitive and fiddly, this vessel has ~ 60 to do, in three different heights, some 3 hole and 2 hole on the forecastle. This picture shows the gig I made to hold them at the right height while soldering And this is one of the 4 stayed stanchions at the gangway entrance set up for silver soldering And here is the full set for one side being painted, with the mast turnbuckles in the background And lastly, installed and ready for the handrail wires The wires are made from 0.2 mm dia coated 7 strand wire, connected using 0.8mm brass tube, compressed to hold. Here is a shot of the deck with the wires installed You can see the gangway entrance in the distance, the starboard side one has its chain installed (behind the 3 inch gun) The mast is in and rigged, though this picture is a little out of focus, you can still see the lead fishing weights I use to simulate the insulators installed on the stay wires (those tiny black blobs on the wires), quite noticeable on the pictures of the real vessels Here is a close-up of the lower end rigging Steve 5 Link to comment Share on other sites More sharing options...
Steve D Posted October 15, 2020 Author Share Posted October 15, 2020 Update part two I paint my ensigns, here is the linen set up for painting, the fabric paint lasts a long time when you only paint a flag a year at most, these tubes are 30 years old and still fine, a lifetime purchase... First side done Once painted on both sides, the edge is painted with varnish to prevent fraying and its cut out, soaked in weak PVA and clamped in position to dry And finally, installed on the mid-ships jack, which to the pictures seems to be where they were run up Also in this picture you can see the life-buoys finished and one of the 5 carley floats installed, note the flags in the flag locker and other details sorted out Here is the forecastle with everything secured in place, cover on the boat rolled back to show the interior detail and anchor cable run through the deck sheaves to route past the holman projector So, finally an overview shot, more or less complete in this picture. I'm waiting on the case and the oak board to mount it on. Once that's all complete, I'll post some shots on the "ready for inspection" forum. This is the end of the build thread, thank you for reading it and also for the generous comments and likes, I hope there were points of interest and take away's of use. I'm looking forward to seeing it in the house, probably more than my wife is. Time for a drink methinks Cheers Steve 15 Link to comment Share on other sites More sharing options...
gunzo Posted October 15, 2020 Share Posted October 15, 2020 Sublime Les 1 Link to comment Share on other sites More sharing options...
Jerry L Posted October 15, 2020 Share Posted October 15, 2020 Steve, I have really enjoyed your build, the craftsmanship, and explanation of how you did it. A superb build. I stand in awe and in some lifetime, hopefully, I will be just half as good in building. Thank you for sharing. Bravo Zulu. 1 Link to comment Share on other sites More sharing options...
Steve D Posted October 15, 2020 Author Share Posted October 15, 2020 9 minutes ago, Jerry L said: Steve, I have really enjoyed your build, the craftsmanship, and explanation of how you did it. A superb build. I stand in awe and in some lifetime, hopefully, I will be just half as good in building. Thank you for sharing. Bravo Zulu. Thanks for the kind comment, 25+ years in and I'm still learning and making more mistake than components. Really, given the time and energy I spend, I should be better I just hope people feel this technique (use metal for metal and wood for wood etc) is not just possible but assailable and so not limit ambition to kits Steve Link to comment Share on other sites More sharing options...
JohnWS Posted October 15, 2020 Share Posted October 15, 2020 Another terrific build, Steve. I really enjoyed following along, learning from your metal work experience & about this very unique vessel. John 1 Link to comment Share on other sites More sharing options...
robgizlu Posted October 15, 2020 Share Posted October 15, 2020 Love that ensign and love those stanchions I agree with all of the above - this blog has been a pleasure to follow and is hugely inspirational Rob 1 Link to comment Share on other sites More sharing options...
longshanks Posted October 15, 2020 Share Posted October 15, 2020 The cherry on the cake with the stanchions and flags Avoid numpties and stay safe Kev 1 Link to comment Share on other sites More sharing options...
stevehnz Posted October 15, 2020 Share Posted October 15, 2020 A wonderful build Steve. That truly is a masterpiece. I've thoroughly enjoyed following the thread & have gained a greater understanding of the SGBs, long a favourite. I would be quite happy with a 1/72 kit now. Steve 1 Link to comment Share on other sites More sharing options...
Courageous Posted October 16, 2020 Share Posted October 16, 2020 A fantastic build, so much skill and detail. Enjoy your respite, looking forward to you next challenge. Stuart 1 Link to comment Share on other sites More sharing options...
Steve D Posted October 16, 2020 Author Share Posted October 16, 2020 21 minutes ago, Courageous said: looking forward to you next challenge. Thanks Stuart and of course to all the other kind comments. These coastal forces models need to be joined by the enemy to place it all in context. My research into the Type 38 Schnellboot (without the armoured cupola) is at the drawing stage now, I'll start that thread next week. Overall, it's a simpler model but the hull lines are quite subtle as I'm discovering with the drawing At 1/48th scale, that's a model ~ 28 inches long, nice size, pretty much the same as the Fairmile B Steve 1 Link to comment Share on other sites More sharing options...
Dancona Posted October 16, 2020 Share Posted October 16, 2020 This has been an inspirational build, I have been a closet follower for sometime and will sorely miss it, what you have achieved there is another true masterpiece, look forward to seeing it on RFI ! Cheers David 1 Link to comment Share on other sites More sharing options...
Iceman 29 Posted October 16, 2020 Share Posted October 16, 2020 Incredible work! Bravo! 1 Link to comment Share on other sites More sharing options...
Brandy Posted October 16, 2020 Share Posted October 16, 2020 I'm not a maritime guy, but a great model is a great model, no matter the subject. This is gorgeous, and your build thread has been very interesting and informative. I've probably learned more nautical terms here than in my entire life up to now. Even if I don't really understand what they mean! Ian 1 1 1 Link to comment Share on other sites More sharing options...
Steve D Posted October 16, 2020 Author Share Posted October 16, 2020 6 hours ago, Dancona said: I have been a closet follower for sometime and will sorely miss it Thanks David, hopefully, you won't have long to wait, the Schnellboot thread will start next week. I started this one with the intention to provide all the information necessary for others to make a similar model. But, to be honest, the guns among other things were quite hard and probably not suitable for a first scratch build. I've been studying the S-boat and it certainly could be a first scratch build. My hope is to make it available in component form if others want to build one (think ambitious kit). The frames will be a CAM sheet from 4d or similar, the etching sheets will be available and printed components I can make or forward the 3d models. I'll explain all this in that thread 4 hours ago, Iceman 29 said: Incredible work! Bravo! Ha, nice of you to post those two juxtaposed, 9 months between the two states, not so shoddy... 2 hours ago, Brandy said: I've probably learned more nautical terms here than in my entire life up to now. Thanks Ian, I'm always very keenly aware that there are people on this forum who actually served and know what they are talking about so I'm very conscious of trying to use the correct terms 2 Link to comment Share on other sites More sharing options...
Iceman 29 Posted October 16, 2020 Share Posted October 16, 2020 "Ha, nice of you to post those two juxtaposed, 9 months between the two states, not so shoddy..." It's your baby now! 😂 You'll have to avoid leaks! 😜 1 Link to comment Share on other sites More sharing options...
beefy66 Posted October 16, 2020 Share Posted October 16, 2020 6 minutes ago, Iceman 29 said: "Ha, nice of you to post those two juxtaposed, 9 months between the two states, not so shoddy..." 9 Months and not so Shoddy just goes to show that some people just have to much time on their hands brilliant stuff Steve great WIP this has given more than me some serious thought about trying this stuff but maybe in a smaller scale for now Stay Safe beefy 2 Link to comment Share on other sites More sharing options...
Steve D Posted October 16, 2020 Author Share Posted October 16, 2020 1 hour ago, beefy66 said: some people just have to much time on their hands 46 years at work without a gap and hardly a day missed, makes a nice change to have the time to indulge I've never had so much time on my hands 1 Link to comment Share on other sites More sharing options...
Steve D Posted October 18, 2020 Author Share Posted October 18, 2020 Post-script After that post, I realised that I'd not closed the story on the mystery box. I still have no clue what it's for or what I does, but I thought making it might help (in copper, naturally) That is to the drawing and it does bare a resemblance to the pictures. Here it is in white primer on the deck where it goes (could it be a tool box for the torpedo tube possible?, or stowage for boat fenders, it is right by the gangway after all?). On the best picture, you can just make out that its on short legs so 1 mm x 1mm brass angle was used. That top is sooo... strange, I'd love to know what it is The oak is on order, but I made up the mounting columns, the aim it to have it seem to float in the air. The forward one locates with a brass bar into a tube in the keel, keeping it upright, mounted below on some scrap chipboard Steve 10 Link to comment Share on other sites More sharing options...
Rod Davies Posted December 23, 2021 Share Posted December 23, 2021 Hi all, A great build. I might be able to shed some light on the mysterious boxes near the torpedo tubes. One reference I used a long time ago said that there were paraffin tanks on the upper deck for replenishing the torpedo engine heating paraffin. Looking at those boxes, I suggest they may be the storage tanks with an additional screening cover to reflect heat from the sun as used to be fitted on the top of pyrotechnic tanks too. Rod. 2 1 Link to comment Share on other sites More sharing options...
Steve D Posted December 23, 2021 Author Share Posted December 23, 2021 4 hours ago, Rod Davies said: One reference I used a long time ago said that there were paraffin tanks on the upper deck for replenishing the torpedo engine heating paraffin. Hi Rod, That's really interesting, you may well be on to something there. On Medea, there was a square rack for petrol tin storage for the motor tender (those old rectangular petrol tins) that is about the same size, I'd not thought of that Cheers Steve Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now