Jump to content

Patrol Torpedo Boat PT-579 / PT-588 (05165) - 1:72 Revell


Julien

Recommended Posts

Patrol Torpedo Boat PT-579 / PT-588 (05165)

1:72 Revell

 

spacer.png

 

PT Boats by their very name are Patrol Torpedo Boats. They are smaller fast attack craft designed primarily to launch torpedoes at enemy vessels using their fast speed as a their primary advantage.  Elco were the makers of the longest, and most produced of these PT Boats made for the US Navy. Even though the main armament was four torpedoes later towards the end of the war some boats received two eight cell Mark 50 rocket launchers.  These launched 5" spin stabilised Mark 7 and Mark 10 rockets. These had a range of upto 11,000 yards. These were equivalent to a 5" shell from a destroyer and the PT Boats carried 16 in their tubes with 16 reloads. This gave these Boats quite a punch. 

 

 

The Kit

This is re-issue of Revell's new tool kit from 2018 with new parts to reflect the different armament of these boats, namely the rocket launchers and the 37mm M4/M9 autocannon which was not in the previous kit. In addition this kit features the lightweight 22.5" Mark 13 torpedoes on lightweight roll-off type racks, over the Mark 8 21" torpedoes in Mark 18 tubes which again were on the earlier release. As well as the main hull parts there are a further 11 sprues of grey plastic and a clear sprue. Construction begins with the hull. The left and right parts are joined with a centre bulkhead being added to stiffen things up. A small insert is added into the bow. The lower hull part at the back is separate and this needs to be added in. The transom will need to be added in, though or some reason this is not mentioned in the instructions! its not there in step 3 but appears in place in step 7? The inside parts of the deck houses must be added to the main deck and this can then be joined to the lower hull. The upperdeck is then fitted out with a myriad of deck fittings, hatches and other parts. Moving to the bottom of the hull the prop shafts and rudder are added. The stand for the boat can then be made up and used if need. Finally on the transom the exhausts are added. 

 

spacer.png

 

spacer.png

 

spacer.png

 

Moving to the top the model the superstructure is made up along with its internal parts. The side gun mountings are also made up and added at this time. For the aft deck the 40m Bofors and its mount are built up and added on. On the foredeck both the 37mm auto cannon and 20mm Oerlikon are completed and mounted. Next up the main armament of the 22.5" Mark 13 torpedoes are added along with their roll off racks.  The radar mast is made up and mounted to the main deckhouse roof which can then be added to the model. The double machine gun units can then be added to the mounts previously installed.  Last up the 5" rocket launchers are made up and mounted to the deck. 

 

spacer.png

 

spacer.png

 

spacer.png

 

Markings

The decal sheet has markings for PT-588 & PT-579 from Engine Torpedo Boat Squadron THIRTY NINE (PTRon 39), Pacific Fleet, Samar, P.I., July 1945.

 

spacer.png

 

Conclusion

Its good to see this out representing the later model of the PT boat with the increased firepower. Highly recommended.

 

 

bin.jpg

 

Revell model kits are available from all good toy and model retailers. For further information visit

 logo.jpg t_logo-a.png or facebook.gif

  • Like 4
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...