Jump to content
This site uses cookies! Learn More

This site uses cookies!

You can find a list of those cookies here: mysite.com/cookies

By continuing to use this site, you agree to allow us to store cookies on your computer. :)

Jim Bates

Anouther Victory Build

Recommended Posts

Always wanted to make a model of  the  HMS Victory sailing ship after weighing up the pros and cons I decided on the Heller Victory the scale of 1/100 appeals not to big and large enough for small parts to be made.

Looking through the instructions it looked daunting for a first time  build.

I reasoned it out that breaking it down to sections at a time and learning as I go hopefully will complete it.

I resisted sticking the hull together as it’s easier to paint in two halves.

Found out about self adhesive copper tape only two thou thick it went on surprisingly easy and when rubbed in gave a good impression of copper plates. Left out the bow section copper until the two halves were together

 

I thickened up the gun ports with evergreen strip as the hull sides were notably far to thin in these areas

Wondered why Heller specified red for the lower deck why?

I decided to plank the lower decks with wood.

 

Recent Victory builds on various sites are a good source of information and inspiration for a novice.

 

victory-build.jpg

build2.jpg

Share this post


Link to post
Share on other sites

Jim

Nice start.

Don't know about red - all interior photos of HMS victory show natural wood for decks or pale colours for walls, doors etc.

Nice yellow/ochre - what brand/colour is it?

Cheers

Share this post


Link to post
Share on other sites
8 hours ago, Jim Bates said:

Wondered why Heller specified red for the lower deck why?

Gidday Jim, good start with the model. I read many years ago that the insides of the gun decks were painted red so that during the carnage of battle the blood wouldn't show. I don't know if it true or not but considering Nelson's tactic of "going straight at 'em", lay alongside and then pound each other to matchsticks and gruel I wouldn't be surprised. On this happy note, Regards, Jeff.

Share this post


Link to post
Share on other sites

The planking went well so at last got the sides together.

 

In fitting the lower deck supports some were to small even after making sure I had the right ones? So  have to make up wooden ones they will be stronger-than the kit ones.

The lower deck was a tad oversize but soon  filed it down to fit.

 

 

 

Cannons next so made up only what I needed for the deck I was working on as there is quite a bit of repetitive work in them.

Started to paint the parts on the spruce but then found out the plastic should be unpainted before glueing all part of the learning curve!

Made up a small jig for the front wheels and sides of the cannons to keep things square.

Not sure the best way to secure the cannons to the decks as I didn’t want them coming lose once  the decks were buttoned up. So I used  Araldite maybe a bit over the top?

Having trouble uploading photos?

Edited by Jim Bates
Trying upload pictures

Share this post


Link to post
Share on other sites
20 hours ago, Jim Bates said:

Not sure the best way to secure the cannons to the decks as I didn’t want them coming lose once  the decks were buttoned up. So I used  Araldite maybe a bit over the top?

Gidday Jim, to attach small parts to a deck (or bulkhead) I sometimes drill a small hole into the bottom of the part where it can't be seen, another hole in the deck under the part and join them with a short piece of thin styrene rod. This also makes painting easier if the part is to be a different colour to the deck. Paint them separately before attaching them. HTH. Regards, Jeff.

Share this post


Link to post
Share on other sites
On 03/12/2019 at 03:03, Pak75 said:

Jim

Nice start.

Don't know about red - all interior photos of HMS victory show natural wood for decks or pale colours for walls, doors etc.

Nice yellow/ochre - what brand/colour is it?

Cheers

For the outside I am using Humbrol enamel 71 /33

Share this post


Link to post
Share on other sites
46 minutes ago, Jim Bates said:

Annoyingly I cant upload pictures what do I have to do??? 

ok now have sorted the uploading of the pictures

Share this post


Link to post
Share on other sites

Next I reinforced each of the masts with brass rod machined to fit into the mast  centres to stiffen them up  painting went well.

A Photo to show how its progressing.

I cant download image again?? I might have been trying to up load the full file in stead of my reduced one so here we are

spacer.png

Share this post


Link to post
Share on other sites

 

Sent off for some blocks and rigging lines from www. HiSModel.com

 

 

 And photo- etch from www.dafinismus.de/index

 

 I must say this is first class photo etch it will bring out the best on my Victory

 

Next up made and fitted the channels and using Daffi photo etch for the channel irons. I tried to glueing  the irons with superglue at first but couldn’t get proper results.

 

 So out came the soldering iron from the back of the shed that tested my skill as I haven’t had to solder for years after a shaky start soon got into the swing of it was quite pleased with the end result.

This is probably the hardest part of the build so far.

Counted up all the deadeys I would need and got them from Caldercraft fitted into the etch very well.

Share this post


Link to post
Share on other sites

Thanks Colin  I was surprised how easy it was to fit now I am undecided weather or not to apply a clear varnish to it.

Share this post


Link to post
Share on other sites

Cannons are a bit fiddly so,

 Here is a picture of my jig for the cannons made out of scrap plastic,

 This keeps the front wheels square to the cannon sides  so much easier.

spacer.png

Edited by Jim Bates
forgot tex

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...