Jump to content
This site uses cookies! Learn More

This site uses cookies!

You can find a list of those cookies here: mysite.com/cookies

By continuing to use this site, you agree to allow us to store cookies on your computer. :)

Recommended Posts

A build from 5 years ago:

 

If Mig is a recognizable name in the aviation world, this particular plane, the Utka (duck in Russian) may be not so. Designed along the lines of the canard (again, duck, this time in French) lines of so-(wrongly)-called  tail-first, it joins the multiple planes built by a number of manufacturers using that formula.

I was surprised of finding this plane as a kit, and I am happy Avis, the manufacturer that released it, decided to present this attractive and unusual civil aviation design.

Congratulation Avis on releasing an appealing and unusual civil subject.

At approximately the same time, a resin kit appeared in the market. This other resin kit by Jet & Prop seems to be nice and very refined, but, alas, as usual, with a much bigger tag price.

This resin kit presents a different solution for the transparent parts, presenting the whole area as a clear part, a much better approach than the one taken by this injected kit by Avis, which only has individual panes that are rather thick and not absolutely clear.

The Avis kit though has some degree of detail overall, however it gives a general impression of heaviness (short run technology). The surface detail is fair, and it has interior details too, if again not particularly refined.

No decals are provided, nor photoetched parts or masks. You are on your own to create painting masks for the design, which has a certain degree of complexity.

Some flash and mold lines are present on the parts and all require cleanup. The engine/prop pack is designed to allow the prop to freely rotate.

The price of this kit is very convenient, and you get a nice replica of an unusual plane, so for me it seems not a bad deal overall.

The kit represents one of the many iterations this design went through, so study your photos and references.

It is likely that this one may have a propensity towards tail-sitting, so it would be wise to load some weight inside the nose, just in case.

My thanks to Mr. Christos Psarras of Parabailarlabamba, and Deimos and Phobos, his dogs, for facilitating the acquisition of this lil' kit.

 

If a little laborious and requiring some patience and skill, it is a fair price to pay for an unusual design:

42.jpg

 

43.jpg

 

46.jpg

 

49.jpg

 

51.jpg

 

55.jpg

 

56.jpg

 

If the mythical Tour D'Argent restaurant in Paris produces arguably the best pressed duck, the duck that Avis pressed in its molding machines is not so great.

There a few things that need correction, and some could benefit from improvement, but even if you build it OOB it would be an acceptable model (provided that you bend the wing down to achieve the necessary anhedral).

This is a smallish but appealing subject provided by this triple-identity manufacturer, which has a stamped manufacturer seal on one side of the sprue tree that reads "AMODEL", and "MASTER 44" on the other, whereas "AVIS" is nowhere to be seen in the sprues, but is featured on the box. Mysteries of the Eastern European kit industry.

The parts are a tad chunky, there are no perks (no masks, no decals, no P.E. parts, etc.) and you will need to exercise those modeling skills, given the short-run nature of this release. And you will have to sweat on your own to mask the model in order to achieve its painting scheme.

Summarizing: a nice subject, of a welcome civil nature, a not so great molding and engineering with the limitations of short-run technology, and some amount of work for the modeler due to the lack of masks or even patterns to make the masks for the complex decoration. No decals either, even if the prop needs some.

You get interior details and to some extent exterior details, reasonable, but not among the finest.

As said above, there is a resin kit of this same plane issued by Jet & Prop that looks far better, but it is (alas!) far more expensive too. And you have to deal with resin, which not all of us love.

Do not forget to put some weight inside the model's nose, there is tail-sitting potential here.

This one will make you huff and puff and bit, but unless you have the bucks for the other -resin- kit around, there is not much choice if you want your duck.

 

03.jpg

 

04.jpg

 

07.jpg

 

12.jpg

 

14.jpg

 

15.jpg

 

16.jpg

 

23c.jpg

 

40.jpg

 

29.jpg

 

31.jpg

 

 

Share this post


Link to post
Share on other sites

I surely share your love to obscure and unusual prototypes :)

Not for the first time I enjoy your builds of the models that I'm planning to build or built too. Well done, Sir <hat off!>!

 

Just in case you are interested - this is my build of the same subject, same year(?) of 2014, Prop&Jet kit 

https://www.britmodeller.com/forums/index.php?/topic/234964803-172-propjet-mig-ytka-duck/

 

Share this post


Link to post
Share on other sites

Another very fine build. The build photos are very useful too (as per usual) in case anyone wants to attempt a scratch build or just wished to know what they get for their money. The finish and photos are also first class.

 

P

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...