Spookytooth Posted November 17, 2018 Share Posted November 17, 2018 Well after the disaster of the Me 109 I went to the stash and found this little baby. I purchased this from Modelzone for a dirt cheap price, Four runners in greyish plastic. And a tinted canopy . Finally the decals. A nice selection of decals for both plane and stores too. I will decide which one I am doing towards the end. I am off now to relax before tackling this build in a more controlled manner. All comments welcome. Simon (to be a patient one, this time.) 13 Link to comment Share on other sites More sharing options...
giemme Posted November 17, 2018 Share Posted November 17, 2018 No comment for the moment, just 🍿 and 🍺 Ciao 1 Link to comment Share on other sites More sharing options...
Navy Bird Posted November 17, 2018 Share Posted November 17, 2018 I have this same kit along with the Eduard Big Ed set, and some resin exhausts and cockpit. Looking forward to your build, I hope it goes together well. Any thoughts yet on how you'd like to duplicate that odd metallic sheen to the greys? Cheers, Bill 1 Link to comment Share on other sites More sharing options...
Spookytooth Posted November 17, 2018 Author Share Posted November 17, 2018 4 minutes ago, Navy Bird said: I have this same kit along with the Eduard Big Ed set, and some resin exhausts and cockpit. Looking forward to your build, I hope it goes together well. Any thoughts yet on how you'd like to duplicate that odd metallic sheen to the greys? Cheers, Bill I honestly don`t know Bill, although I am toying with the idea of using Alcads for the exhausts areas. The Revell colour cal outs is for 50 shades of Grey LOL. Simon. 2 3 Link to comment Share on other sites More sharing options...
Sturmovik Posted November 17, 2018 Share Posted November 17, 2018 Is Modelzone still a thing? I thought they had gone bankrupt. What did exactly happen to the Bf 109 that made you throw it away? Link to comment Share on other sites More sharing options...
Spookytooth Posted November 18, 2018 Author Share Posted November 18, 2018 12 hours ago, Sturmovik said: Is Modelzone still a thing? I thought they had gone bankrupt. What did exactly happen to the Bf 109 that made you throw it away? Modelzone went down mate, but I made a few purchases before they did. The 109 was screwed, all the front end was out, I just had enough to be honest. I had a bad day, and it was the final straw. Needless to say, in future I will count to ten. Simon. 1 Link to comment Share on other sites More sharing options...
Hook Posted November 18, 2018 Share Posted November 18, 2018 15 hours ago, Spookytooth said: I honestly don`t know Bill The best pointers I've found so far: http://www.aircraftresourcecenter.com/Gal8/7501-7600/gal7545-F-22-Rotramel/00.shtm Cheers, Andre 1 Link to comment Share on other sites More sharing options...
Spookytooth Posted November 18, 2018 Author Share Posted November 18, 2018 10 minutes ago, Hook said: The best pointers I've found so far: http://www.aircraftresourcecenter.com/Gal8/7501-7600/gal7545-F-22-Rotramel/00.shtm Cheers, Andre Thanks Andre, my skills are probably not up to this guy but its given me some pointers. Hopefully I can do a reasonable job on her. Simon. Link to comment Share on other sites More sharing options...
Spookytooth Posted November 19, 2018 Author Share Posted November 19, 2018 Well, I made a start. She is big, compared to the Martlet I finished recently . But there is a lot of ejector pin marks to get rid of though. Added the controls to the pit before priming/painting. But the seat has an annoying gap at the top to sort out. It lined up OK but why this happened I don`t know, time for some card/filler. Wheels and tanks next, still need to clean the wheels up but the tanks look OK. I am taking time with this one, as I don`t want any more repeats of what happened to the Me 109... All comments welcome. Simon, the cautious one. 10 Link to comment Share on other sites More sharing options...
giemme Posted November 19, 2018 Share Posted November 19, 2018 Caution's paying off, so far! Those ejector pin marks are a royal PITA, aren't they? And she IS big! Ciao 1 Link to comment Share on other sites More sharing options...
Spookytooth Posted November 28, 2018 Author Share Posted November 28, 2018 On 19/11/2018 at 20:47, giemme said: Caution's paying off, so far! Those ejector pin marks are a royal PITA, aren't they? And she IS big! Ciao Yep she sure is Giemme, but not that many parts in all really. 116 to be exact, or that is what is written on the box... Sorry for the tardiness but life... Update. Although I have been busy in life, I got this lot ready for priming. Hopefully I will be able to post some more on the weekend. All comments welcome. Simon. 9 Link to comment Share on other sites More sharing options...
giemme Posted November 28, 2018 Share Posted November 28, 2018 Looking forward to more, Simon Ciao 1 Link to comment Share on other sites More sharing options...
Spookytooth Posted November 29, 2018 Author Share Posted November 29, 2018 Cheers @giemme, a bit more done today... Laid down some primer. Then sprayed some XF 2 down. Sorry about the blurred pic. Then some XF 19. The cockpit tub and I.P. have been given a coat of XF 19. Still more spraying to do, I see some remedial work on the intakes for a start, but thats about it until Saturday at least, mother is visiting... All comments welcome. Simon. 8 Link to comment Share on other sites More sharing options...
giemme Posted November 29, 2018 Share Posted November 29, 2018 It looks a very smooth paint job to me, Simon And the kit has some lovely details too - refreshing build, so far Ciao 1 Link to comment Share on other sites More sharing options...
hacker Posted November 29, 2018 Share Posted November 29, 2018 Despite the kit's minor faults it seems a nice detail kit of a modern aircraft Hacker 1 Link to comment Share on other sites More sharing options...
Spookytooth Posted December 3, 2018 Author Share Posted December 3, 2018 On 29/11/2018 at 19:06, giemme said: It looks a very smooth paint job to me, Simon And the kit has some lovely details too - refreshing build, so far Ciao On 29/11/2018 at 19:14, hacker said: Despite the kit's minor faults it seems a nice detail kit of a modern aircraft Hacker Thanks, the kit has some good details but those ejector pin marks let it down, see below. Well I did not get any thing done over the weekend due to life getting in the way. But looking through bits to do I found these. Yep the dreaded ejector pins have arisen plus sink marks too, come on Revell , you could do better here. Then looking through the pit I noticed that the throttles? had gone AWOL. Sorry about the pic. And here is the bit to make. Another tiny bit to scratch I suppose. Anyhow folks, I hope to be able to give a better update during the week. All comments welcome. Simon, (Slightly miffed). 4 1 2 Link to comment Share on other sites More sharing options...
TheBaron Posted December 3, 2018 Share Posted December 3, 2018 (edited) On 11/19/2018 at 7:52 PM, Spookytooth said: The F22 Mistel under construction! Edited December 3, 2018 by TheBaron 3 Link to comment Share on other sites More sharing options...
giemme Posted December 3, 2018 Share Posted December 3, 2018 Keep it up, Simon - you will prevail Ciao 2 Link to comment Share on other sites More sharing options...
Nikolay Polyakov Posted December 4, 2018 Share Posted December 4, 2018 Hello Simon! You’re did a great job with a higher level of accuracy! Looking forward to seeing more 👍 Cheers! 😎 1 Link to comment Share on other sites More sharing options...
Matt_ Posted December 4, 2018 Share Posted December 4, 2018 On 12/3/2018 at 6:45 PM, Spookytooth said: Sweet Jesus, those sink marks are a whole extra set of panel lines! 🙈 2 Link to comment Share on other sites More sharing options...
Spookytooth Posted January 27, 2019 Author Share Posted January 27, 2019 Hi folks, I am really sorry for not posting recently, but life has thrown in a few curve balls, so to speak. I had a notification from the hospital that I was to have a Cardio Ablation done on the 20th Dec, so I had to get a lot of things done before then. The procedure failed, leaving me in AF still. This has meant that I have had to end my Part-time job as a sound engineer. And at the beginning of the month, my wife had to have an Abscess drained from a place you don`t want it be. That was OK but the nurse made a mistake on the first day of dressing changing so a second op had to be done. Needless to say, I have been busy else where to even touch the bench. But before the Op, I did manage this. Lots of Green Squadron on the outsides. Once rubbed down it did not look that bad, we will see under some Primer. I have decided too, close the main and side weapons bays , to many ejector pin marks visible. Shame but I have to be realistic about my skills. Anyhow folks I will be off now to catch up on what else is happening here on BM. All comments welcome, Simon. 6 Link to comment Share on other sites More sharing options...
giemme Posted January 27, 2019 Share Posted January 27, 2019 (edited) Simon, mate, I'm sorry to hear about all the trouble you and the good Lady Rose had to go through. Stay strong, we're all rooting for you! Ciao Edited January 27, 2019 by giemme 2 Link to comment Share on other sites More sharing options...
Spookytooth Posted January 27, 2019 Author Share Posted January 27, 2019 4 minutes ago, giemme said: Simon, mate, I'm sorry to hear about all the trouble you and the good Lady Rose had to go through. Stay strong, we're all rooting for you! Ciao Thanks mate, Rose is well on the mend now, with maybe one or two more dressing changes before it can be left to itself. I am fine, just awaiting a date for a Cardio Inversion this time. In and out in 4 hours, hopefully. Simon. 2 Link to comment Share on other sites More sharing options...
The Spadgent Posted March 5, 2019 Share Posted March 5, 2019 Nice looking bird. Glad to see you’re getting the better of pin marks. Sorry to hear about your and your better half’s troubles. Fingers crossed for a speedy recovery. I’ll tag Ali g for this on if that’s ok. All the best kid. Johnny boy. 2 Link to comment Share on other sites More sharing options...
Spookytooth Posted March 9, 2019 Author Share Posted March 9, 2019 Thanks Johnny, all is a bit better for now, one can only hope that it keeps going the right way. Anyhow, it`s been over three months since I have posted anything new on this build. Well, I am proud to announce that I finally got on the bench..... Not a great deal of time, for now but actual bench time. First up was the exhaust tunnels. Join seam. OK, out with my trust filler. I left that to dry before a a few swipes of a rat tail file should hopefully hide them. While at it, the inlet tunnels received the same sort of treatment. While they are drying I cut some masks for the exhausts . And in place. I have also started painting the seat as well. Time for a coffee then maybe a bit more. All comments welcome. Simon. 9 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now