Jump to content

Standard B “Liberty” Truck. 1:35


Shar2

Recommended Posts

Standard B “Liberty” Truck

ICM 1:35

 

spacer.png

 

As America's war effort ramped up in 1917, there was a collective realization that the fleet of vehicles needed to support a semi-mechanized army needed some standardization. The Liberty truck was the solution. It was designed by the Motor Transport section of the Quartermaster Corps in cooperation with the members of the Society of Automotive Engineers. A group of leading automotive engineers was summoned to Washington in 1917 to design standardized trucks for the AEF. It took 50 men 69 days to design a 1-½ ton "A" model and the 3–5 ton "B" model. Production of the Liberty B began in the fall of 1917, and the first models were delivered to the secretary of war on 19 October. Of the almost 9,500 produced by 15 manufacturers, more than 7,500 were sent overseas. The Liberty's four-speed transmission coupled with its 52-hp engine gave the truck a top speed of about 15 miles per hour. 

 

The Model

The model arrives in a strong box with a separate top sleeve with a nice artist’s representation of the vehicle on the front. Inside, within a large poly bag, are four sprues of medium grey styrene and, in a separate poly bag, one clear sprue.  On initial inspection the parts are really well moulded, clean, with no sign of flash.  There are a number of moulding pips, some of which are on delicate parts, so care should be taken when removing.  The sprue gates attaching items like the tilt rails are also quite heavy so again take care with their removal and clean-up. 

 

spacer.png

 

spacer.png

 

spacer.png

 

spacer.png

 

spacer.png

 

The build starts with the chassis, with each rail being fitted fore and aft leaf springs, each of two parts. Two of the cross-members are assembled from two parts each before being fitted to one of the chassis rails, along with three other single piece cross-members followed by the other rail. The radiator is then assembled from six parts before being glued into position at the front of the chassis. The single piece front axle is then glued to the front pair of leaf springs and a further cross-member is also glued into place.  The rear differential is made up from fourteen parts which include the rear drum brakes.  The front bumper beam and transfer box are also assembled and glued into position along with t he drive shafts and three piece front mudguards.

 

The front wheels and single piece items with a choice of separate hub caps, the rears being made up of inner and outer wheels with separate tyres and hub caps. The completed wheels are then attached to their respective axles. Work then begins on the engine, which is made up from eleven parts.  Once assembled, it is fitted to the chassis along with the two piece exhaust pipe and silencer. The gearstick is then added to the gearbox and the engine fitted with two more parts. The cabin is then assembled from twenty one parts before being fitted to the chassis over the gearstick, followed by the outer radiator grille, and two piece bonnet, which could easily be made to be posed open to show off the engine, even though it’s not shown posed that way.

 

The next assembly is the truck bed, with the bed itself being fitted with the sides, rear, and front plank sections. On the underside, five lateral strengthening beams, and the sides with four vertical beams each. Two five piece storage boxes are assembled and fitted to the front underside of the bed before the whole assembly is attached to the chassis. There is a five piece searchlight and two piece horn attached to the cabin coaming and the steering wheel is also glued into place at this point. The pair of two piece headlights are attached to the front of the cabin bulkhead, while the bonnet latches, and grab handles, plus the cabin access handles are fitted, as is the starting handle.  The cabin roof is fitted with left and right hand frames before being glue into place, and on the bed the modeller has the option of just fitting the five tilt rails, or the complete canvas cover which is made up from five parts, completing the build.

 

Decals

The small decal sheet gives the modeller just two options of vehicle, both in use by the US army in 1918, one with just unit badges and one with US Quartermaster Corps labelling on the tilt sides. The decals are nicely printed, clear and in good register with a slightly matt finish.

 

spacer.png

 

Conclusion

It’s great to finally see a WW1 Liberty tuck being kitted, especially in this centenary year. ICM have not only provided us with a nice tribute to one of the lesser sung vehicles of the First World War, but a very nice truck to build too. It’s not overly complicated, which is good to see, even though the truck itself was pretty simple, and would be a great kit for any level of modeller.

 

Review sample courtesy of logo.gif

  • Like 3
  • Thanks 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...