fjaweijfopi4j48 Posted August 4, 2018 Share Posted August 4, 2018 (edited) A simple vacuum-formed model from Execuform. This is again for a friend, since my interest on the type is less than nihil. It is posted so it can hopefully encourage those having vac kits and not quite gathering momentum to start one. It's easy, as you will see. I agreed to build it under the condition that it will be completed on a civil paint scheme. Not like this one below, but in a simpler scheme (it gives an idea of the type, though): From Wikipedia: This was surely a vintage edition, since it has white metal parts: Contents of the kit's bag: The white metal accessories: The very simple parts, an Execuform trade mark: And what pilots and modelers like: redundancy! Several canopies vacuformed in thin very clear plastic: In this mold, parts are marked and cut from the back of the sheet, where the parting line is clear: Parts off the backing sheet with no effort: The nice (for the time) white metal parts: The engine even has the cylinder exhaust stacks: All parts free en ready for some little surface detail (there is a plan with the kit, and you have to engrave everything regarding surface detail, even ailerons, flaps, rudder and elevator lines: Edited August 4, 2018 by Moa to add information 7 Link to comment Share on other sites More sharing options...
fjaweijfopi4j48 Posted August 4, 2018 Author Share Posted August 4, 2018 (edited) The nice part of vacs: I nicked an edge, which was easily and quickly repaired adding a sliver of plastic: And then trimmed back and sanded smooth: You can't even tell where it was. So the fear of vacs is mostly unjustified, because repairs are usually easier than with resin or injected kits. Edited August 4, 2018 by Moa to correct typo 8 Link to comment Share on other sites More sharing options...
Space Ranger Posted August 4, 2018 Share Posted August 4, 2018 Execuform kits remind me of some balsa kits from the 1950s with their "pre-cut" parts. The basic shapes are there; you just have to "refine" them. That said, this is probably the only kit of the Timm Tutor we are ever going to see. Only 262 were built, all for the US Navy during WW II, and only 8 remain on the US civil register today. There are also some in museums. Its resin impregnated and molded plywood structure was revolutionary for its time, but did not allow for long-term preservation. The aircraft pictured, N56520, was serial number 204. It was cancelled from the US civil register in August 1970. 2 1 Link to comment Share on other sites More sharing options...
fjaweijfopi4j48 Posted August 4, 2018 Author Share Posted August 4, 2018 13 minutes ago, Space Ranger said: Execuform kits remind me of some balsa kits from the 1950s with their "pre-cut" parts. The basic shapes are there; you just have to "refine" them. That said, this is probably the only kit of the Timm Tutor we are ever going to see. Only 262 were built, all for the US Navy during WW II, and only 8 remain on the US civil register today. There are also some in museums. Its resin impregnated and molded plywood structure was revolutionary for its time, but did not allow for long-term preservation. The aircraft pictured, N56520, was serial number 204. It was cancelled from the US civil register in August 1970. Thanks for the background story, Michael. Link to comment Share on other sites More sharing options...
Martian Posted August 4, 2018 Share Posted August 4, 2018 12 hours ago, Moa said: You can't even tell where it was. So the fear of vacs is mostly unjustified, because repairs are usually easier than with resin or injected kits. Well, we can because you showed us where it was but nicely repaired all the same and that "thing" by Merlin you have on your bench would make almost anything look a doddle! Martian 👾 2 Link to comment Share on other sites More sharing options...
fjaweijfopi4j48 Posted August 5, 2018 Author Share Posted August 5, 2018 Halves glued together and seams treated. The fit is good, and the gauge of the plastic is generous, allowing for comfortable sanding and refining. The wing to fuselage fit requires work and filler. I chose to add the interior (still to be scratched) through the wing opening under the fuselage. Now all the control surfaces have to be engraved: 6 Link to comment Share on other sites More sharing options...
fjaweijfopi4j48 Posted August 6, 2018 Author Share Posted August 6, 2018 (edited) All control surfaces are marked and engraved: Holes for the stab spar, Pitot, landing gear are drilled: Edited August 7, 2018 by Moa 5 Link to comment Share on other sites More sharing options...
fjaweijfopi4j48 Posted August 6, 2018 Author Share Posted August 6, 2018 The elements of the interior are fashioned: A spar is installed for the stab: If you follow the kit's marked lines on the horizontal tail the angle will be wrong (guess how I found out). So I had to put a supplement of plastic at the roots of the stab halves and once dry re-angle: Decals for the inst. panels: A few more details and it will be ready to go in: 9 Link to comment Share on other sites More sharing options...
fjaweijfopi4j48 Posted August 6, 2018 Author Share Posted August 6, 2018 The kit has a very good plan, with abundant detail: Interior furnished: And all goes together: The wing-to-fuselage joint will need plenty of Milliput: 10 Link to comment Share on other sites More sharing options...
fjaweijfopi4j48 Posted August 7, 2018 Author Share Posted August 7, 2018 Since minor variations occurred between airframes, be sure to get photos of your intended subject. In this case the faired headrest was absent, and an anti-roll mast was located between cockpits. The windshields on my model will be curved as on the original plane, not faceted, therefore the kit's transparencies will not be used. 1 Link to comment Share on other sites More sharing options...
k5054nz Posted August 7, 2018 Share Posted August 7, 2018 I had a vague idea what the aircraft was but I fear I fell in love with the photo of the real deal! What a lovely build! 1 Link to comment Share on other sites More sharing options...
Horatio Gruntfuttock Posted August 7, 2018 Share Posted August 7, 2018 Looks like a nice simple vacform - always good to cut one's teeth on these. I have built 35-40 vacs and enjoy the challenge - real modelling skills, although mine often cause cock-ups! This should look mighty purdy in civil colours. 1 Link to comment Share on other sites More sharing options...
fjaweijfopi4j48 Posted August 7, 2018 Author Share Posted August 7, 2018 (edited) The anti-roll mast is fashioned. It will be added later since it was painted in a different color than the fuselage on the plane I am representing: Edited August 8, 2018 by Moa 6 Link to comment Share on other sites More sharing options...
Nikolay Polyakov Posted August 7, 2018 Share Posted August 7, 2018 Thanks for the great story @Moa, now the vacuum-form models are explained. Very impressive work, have a good luck! Cheers! 🙃 1 Link to comment Share on other sites More sharing options...
fjaweijfopi4j48 Posted August 7, 2018 Author Share Posted August 7, 2018 16 minutes ago, Nikolay Polyakov said: Thanks for the great story @Moa, now the vacuum-form models are explained. Very impressive work, have a good luck! Cheers! 🙃 Hi Nikolay! Not sure the vacs were explained, but at least it's a reasonable glimpse on that particular media. I have posted here at Britmodeller some other vacs. In general building them is a pleasant experience for me. Cheers 1 Link to comment Share on other sites More sharing options...
fjaweijfopi4j48 Posted August 8, 2018 Author Share Posted August 8, 2018 Primer is applied: 8 Link to comment Share on other sites More sharing options...
Nikolay Polyakov Posted August 9, 2018 Share Posted August 9, 2018 On 07/08/2018 at 23:10, Moa said: Not sure the vacs were explained, but at least it's a reasonable glimpse on that particular media. Now the vacs are not so mysterious and complicated for me (from the first look). On 07/08/2018 at 23:10, Moa said: I have posted here at Britmodeller some other vacs. In general building them is a pleasant experience for me. Thanks, I’ll check them! Cheers! 🙃 Link to comment Share on other sites More sharing options...
Sabrejet Posted August 9, 2018 Share Posted August 9, 2018 Another lovely vac, being done better justice than it deserves! Inspiring. 1 Link to comment Share on other sites More sharing options...
Britman Posted August 9, 2018 Share Posted August 9, 2018 That's a nice gutsy looking aeroplane, new to me. Following a nice build. Keith. 1 Link to comment Share on other sites More sharing options...
Azgaron Posted August 9, 2018 Share Posted August 9, 2018 Nice work so far! Håkan 1 Link to comment Share on other sites More sharing options...
fjaweijfopi4j48 Posted August 9, 2018 Author Share Posted August 9, 2018 Some bumpies are added: 9 Link to comment Share on other sites More sharing options...
Courageous Posted August 10, 2018 Share Posted August 10, 2018 Effortless work Moa. I wish I could build at your rate. Stuart 1 Link to comment Share on other sites More sharing options...
fjaweijfopi4j48 Posted August 10, 2018 Author Share Posted August 10, 2018 9 minutes ago, Courageous said: Effortless work Moa. I wish I could build at your rate. Stuart I think this is the first time I have been insulted with a compliment. Effortless? 1 Link to comment Share on other sites More sharing options...
fjaweijfopi4j48 Posted August 11, 2018 Author Share Posted August 11, 2018 The white base coat is applied, other parts are painted: 7 Link to comment Share on other sites More sharing options...
Terry1954 Posted August 11, 2018 Share Posted August 11, 2018 Superb work there yet again Moa! I need to catch up on your other builds. Terry 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now