Jump to content

IJN Destroyer Fubuki. Super Drawing in 3D


Shar2

Recommended Posts

IJN Destroyer Fubuki

Kagero Super Drawings in 3D

fc.jpg

 

The IJN’s plans called for 24 Fubuki-class destroyers. These were produced in two groups of ten, the Special Type I and the Special Type II which were distinguished by several technical differences. Type A turret, while the Type II had the Type B turret. The last four ships that were to be produced featured so many changes from the original design that they were redesignated as the Akatsuki-class.

 

Despite the advantages of the Fubuki-class, it was not without problems. The design was overweight from the outset, which caused serious stability issues. There were also concerns with the structural integrity of the design. On September 26, 1935, the IJN fleet ran into a typhoon at sea. Two Special Type destroyers lost their bows, three more suffered severe structural damage, and six others had hull damage. As a result, from November 1935 to 1938 all of the Fubuki-class were sent back to the shipyards for hull strengthening and weight reduction. A ballast keel and an additional 40 tons of ballast were added. To lighten the topside of the ship, whose weight was the partial source of instability, a number of measures were taken: the bridge was reduced in size, smoke stacks were shortened, the number of torpedo reloads reduced, and magazine storage for the main guns was reduced. The result of these efforts was that the displacement was increased to 2,090 tons and top speed reduced to 34 knots, but the stability concerns had successfully been addressed.

 

page1.jpg

 

During the Pacific War, the Fubuki saw extensive service. For example, the Shikinami, which was assigned to Destroyer Division 19, was responsible for finishing off the cruiser USS Houston at the Battle of Sunda Strait during early 1942, participated in the Second Naval Battle of Guadalcanal from November 12-15, 1942, survived the Battle of the Bismarck Sea in 1943, and was finally sunk by the submarine USS Growler on September 12, 1944. Another Fubuki-class, the Amagiri, was the ship responsible for sinking John F. Kennedy’s PT-109 on August 2, 1943. It was later sunk by a mine in the Makassar Strait on April 23, 1944. As the war progressed, surviving Fubuki were modified to increase their survivability. Anti-aircraft armament was increased first to 2 x 13mm twin mounts, then to 2 x 25mm triple mounts, then to even more 25mm triple mounts, with some destroyers apparently being armed with as many as fifteen triple 25mm mounts. Seven of the destroyers were also eventually fitted with No. 22 radars, but the first was not installed on the Yugiri until November 1943, long after the tide of the war had shifted in favour of the Allies. Eighteen of the class were sunk- six to Allied submarines, seven to aerial attack, three to Allied surface ships, and two to mines. Only one of the destroyers, the Ushio, survived the war (another destroyer, the Miyuki, was sunk in a collision in 1934).

 

page2.jpg

 

This is the latest book from Kagero in their Super Drawings in 3D, and like the previous books it has a brief history and the ships specifications at the beginning. This includes the following:-

 

  • Overview
  • Design, Propulsion and Armour
  • Armaments
  • Service Record
  • Conclusion

 

The rest of the ninety three pages are filled with the now well known style of beautifully drawn 3D renderings of every part of the ship.  It is obvious that a lot of time has been taken to get the drawings this good and accurate, and there is a wealthy of information for the modeller to use during their build. Every area of the upper hull and superstructure is dealt with plus the lower hull including the propellers and rudder.  I particularly like the renderings of the torpedo launchers and the turrets and ships boats, plus the interior of the bridge with the paraphernalia contained therein. She certainly was a very good looking ship, even with the unbalanced main armament with one turret forward and two aft.

 

page3.jpg

 

For even more detail, especially for the rigging, Kagero have included a double sided A2 fold out sheet with a three view on one side, unusually in 1:200, with additional drawings of the fore and aft views, ships fixtures, such as bridge, funnels, AA platforms and radar, most of which are in 1:100 or 1:50 scales.

 

Conclusion

This is another superb book in the series and a great addition to any maritime modeller’s library.  This series is a boon to any ship modeller and is turning into a magnificent collection of titles. The detail included is second to none, and the renderings are so clear that they will be a delight for the superdetailers, particularly if building the Tamiya, Pit-Road and Yamashita Hobby kits in 1:700.

 

bin.jpg

 

 

Review sample courtesy of
logo.gif

  • Thanks 1
Link to comment
Share on other sites

Lovely review - I should also add there is a lovely series of kits in 1/350 Scale by Fine Molds of Japan ( very detailed and accurate ) of the Fubuki Class

and you can add aftermarket 5 inch Brass Barrels and brass + etch AA 25mm guns ( from Infini ) - althought there is not an dedicated etch ' Up-Grade Set ' for the Fubuki , you could cobble a few things

from the etch sets for the Kagero Class , possibly

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...