snapper_city Posted July 1, 2018 Author Share Posted July 1, 2018 Here is how things look after a spray of Testors Dullcote over the pigment areas. It has muted the colours which I wasn't expecting but I think I prefer it. Looking back maybe it was a bit too stark before. IMAG5559 by Mark Inman, on Flickr IMAG5561 by Mark Inman, on Flickr Here I have added gun metal pigments to the track horns as these would show signs of wear. IMAG5562 by Mark Inman, on Flickr IMAG5563_1 by Mark Inman, on Flickr The tracks are finally on. Even though I still have quite a bit to do it's one of those big moments that makes you feel closer to the end. IMAG5565 by Mark Inman, on Flickr IMAG5567 by Mark Inman, on Flickr Until next time. 11 Link to comment Share on other sites More sharing options...
crushkill Posted July 6, 2018 Share Posted July 6, 2018 This is looking great, can’t wait to see it done Link to comment Share on other sites More sharing options...
snapper_city Posted July 6, 2018 Author Share Posted July 6, 2018 6 hours ago, crushkill said: This is looking great, can’t wait to see it done Me too. I have now weathered the sides and rear also. Hopefully get an update up over the weekend. 1 Link to comment Share on other sites More sharing options...
snapper_city Posted July 20, 2018 Author Share Posted July 20, 2018 Hi guys Here is how things are looking now. 20180708_094946 by Mark Inman, on Flickr 20180708_095019 by Mark Inman, on Flickr 20180708_095034 by Mark Inman, on Flickr 20180720_231931 by Mark Inman, on Flickr 20180720_232000 by Mark Inman, on Flickr 20180720_232613 by Mark Inman, on Flickr Until next time. 12 Link to comment Share on other sites More sharing options...
Carius Posted July 21, 2018 Share Posted July 21, 2018 (edited) Excellent progress Mark Edited July 21, 2018 by Carius Link to comment Share on other sites More sharing options...
Kris B Posted July 21, 2018 Share Posted July 21, 2018 Looks very realistic. Link to comment Share on other sites More sharing options...
Etienne Posted July 21, 2018 Share Posted July 21, 2018 Really nice !! The dusting looks very realistic 😎 What did you use for the chicken wire rolled fence ? Cheers, E Link to comment Share on other sites More sharing options...
snapper_city Posted July 21, 2018 Author Share Posted July 21, 2018 31 minutes ago, Etienne said: Really nice !! The dusting looks very realistic 😎 What did you use for the chicken wire rolled fence ? Cheers, E The fence is made from Tulle fabric. I got it from Hobbycraft. Even asking for the smallest cut they could do will last me for years and years. 2 Link to comment Share on other sites More sharing options...
Ripaman Posted July 22, 2018 Share Posted July 22, 2018 That looks brilliant Mark inside and out Regards Richard Link to comment Share on other sites More sharing options...
badger Posted July 26, 2018 Share Posted July 26, 2018 Looking really good and a nicely believable level of filth. Love the scratches on the sides - must remember that. I still need to build my Tamiya ACAV that I've had at least 15 years! All the best Ben Link to comment Share on other sites More sharing options...
FrancisGL Posted July 26, 2018 Share Posted July 26, 2018 Great progress, very nice interior, looks real and dirty... Cheers Mark Link to comment Share on other sites More sharing options...
phildagreek Posted July 27, 2018 Share Posted July 27, 2018 Looks excellent! Link to comment Share on other sites More sharing options...
Jeff Leiby Posted July 27, 2018 Share Posted July 27, 2018 Looking good. Just a couple comments based on my experience manning M113-family vehicles. The U-shaped ridge around the rear ramp opening and the "bar" across the top of the rear opening are rubber gaskets and should be painted flat black. Looks like you might still be able to paint the gaskets. AFV Club added the oval plate on the roof at the driver-side rear corner. This plate was not on production M113A1s. It was found only on Pilot #3 so the oval engraving should be filled and the bolts sanded off. For your build, you could cover it with stowage...plenty of photos show stowage at that location. Sorry that I did not see your build earlier, but you have an excellent build underway. I highly recommend David Dolye's two books on the M113, "M113 APC in Vietnam," and "M113 Armored Personnel Carrier Walk Around." AFV left a lot of interior items out of the kit and the biggest mistake is not including engine grill mesh in the provided PE set. Eduard already has a new PE set for this kit on the market. Mark, again a great build, especially like the aluminum undercoat for the interior. Look forward to more of your work. . Link to comment Share on other sites More sharing options...
GMK Posted July 27, 2018 Share Posted July 27, 2018 (edited) 7 hours ago, Jeff Leiby said: AFV Club added the oval plate on the roof at the driver-side rear corner. This plate was not on production M113A1s. It was found only on Pilot #3 so the oval engraving should be filled and the bolts sanded off. For your build, you could cover it with stowage...plenty of photos show stowage at that location. . Jeff, You’re right about the plate around the fuel-filler cap on production M113A1, however a lot of gasoline M113 were converted to M113A1 and the fuel tank (with its oval cut out on the hull roof) with the fuel cell. Most of my (Australian) M113A1s we’re so modified, and this was 1998-2000. Edited July 27, 2018 by GMK ETA: pic 1 Link to comment Share on other sites More sharing options...
snapper_city Posted August 8, 2018 Author Share Posted August 8, 2018 On 7/27/2018 at 4:34 PM, Jeff Leiby said: Looking good. Just a couple comments based on my experience manning M113-family vehicles. The U-shaped ridge around the rear ramp opening and the "bar" across the top of the rear opening are rubber gaskets and should be painted flat black. Looks like you might still be able to paint the gaskets. AFV Club added the oval plate on the roof at the driver-side rear corner. This plate was not on production M113A1s. It was found only on Pilot #3 so the oval engraving should be filled and the bolts sanded off. For your build, you could cover it with stowage...plenty of photos show stowage at that location. Sorry that I did not see your build earlier, but you have an excellent build underway. I highly recommend David Dolye's two books on the M113, "M113 APC in Vietnam," and "M113 Armored Personnel Carrier Walk Around." AFV left a lot of interior items out of the kit and the biggest mistake is not including engine grill mesh in the provided PE set. Eduard already has a new PE set for this kit on the market. Mark, again a great build, especially like the aluminum undercoat for the interior. Look forward to more of your work. . Thanks for pointing these out. I have since painted the rear door gaskets. Unfortunately the oval plate will have to stay at this stage. If it was pre-painting I would have rectified it but not at this late stage. One thing I will remember for when I build another one. I am going to be having a crate with a chair strapped to it in that area. I started this kit originally back in January for a 3 month SIG on another forum. I have missed the deadline by quite a bit but in those early stages I was racing for the line. I would have loved to have gone to town scratch building lots of internal missing detail. It just wasn't a priority due to limited time to complete the build back then. Also apologises for the picture quality over the last couple of posts. I have a new phone and I don't think the camera is as good as my 3 year old one. This will probably be the final update before I'm calling it finished so here is how she looks currently. Here the Legend resin PRC-77 radio has had a bit of updating. 20180710_223707 by Mark Inman, on Flickr Weapons fitted. 20180807_220058 by Mark Inman, on Flickr 20180807_220153 by Mark Inman, on Flickr The PRC-77 fitted to the side of the ACAV cupola armour. 20180807_220225 by Mark Inman, on Flickr Trying to find a modern tooled M79 grenade launcher proved to be a challenge. One can be found in a few Dragon weapon sets and Bravo 6 also do one in resin. Try finding these for sale anywhere close to the UK though is the problem. In the end I found a 44 year old Tamiya one in the spares box. It is quite basic so I drilled the barrel and scratch built the fore end ladder sight. 20180807_220245 by Mark Inman, on Flickr The Tasca M2 Browning with Live Resin ammo is looking sharp. 20180807_220302 by Mark Inman, on Flickr 20180807_220325 by Mark Inman, on Flickr As I said before this will most likely be my final update for the WIP. Once I have it finished and RFI pictures done I will link it here. Many thanks to all that have followed and contributed on the build thread. Peace... 7 Link to comment Share on other sites More sharing options...
PZRGREN Posted August 8, 2018 Share Posted August 8, 2018 Crackin' build! Inspirational! Thanks for the updates, Roger. Link to comment Share on other sites More sharing options...
Aerofix Posted August 17, 2018 Share Posted August 17, 2018 Absolutely stunning. I thought the inside was real at first glance. Link to comment Share on other sites More sharing options...
J.P. Posted August 17, 2018 Share Posted August 17, 2018 On 7/1/2018 at 8:53 AM, snapper_city said: Here is how things look after a spray of Testors Dullcote over the pigment areas. It has muted the colours which I wasn't expecting but I think I prefer it. Looking back maybe it was a bit too stark before. IMAG5559 by Mark Inman, on Flickr IMAG5561 by Mark Inman, on Flickr That looks much better toned down like that...IMO it was too heavy in the before clear coat pictures. The scratches down the side look too. Link to comment Share on other sites More sharing options...
snapper_city Posted August 18, 2018 Author Share Posted August 18, 2018 Quick update. She is finished apart from the rear ramp pulley needs painting and installing. I have ordered a couple of RB Models antennas which should arrive early next week. I also looked through my bases today but they are all far too big. You know what they say. Proper planning prevents p!$$ poor performance. 1 Link to comment Share on other sites More sharing options...
snapper_city Posted August 23, 2018 Author Share Posted August 23, 2018 All finished. Thanks to all those who followed the build. RFI Here DSC_8164 by Mark Inman, on Flickr 7 Link to comment Share on other sites More sharing options...
FrancisGL Posted August 26, 2018 Share Posted August 26, 2018 Looks fantastic!, full of details that bring reality. Cheers mate 👍 Link to comment Share on other sites More sharing options...
gpal Posted August 28, 2018 Share Posted August 28, 2018 Great job, I love the weathering. George Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now