Vitaliy Posted November 29, 2017 Author Share Posted November 29, 2017 (edited) Mark thank you! I'm very wait to see the finished my birdie... Edited November 30, 2017 by Vitaliy Link to comment Share on other sites More sharing options...
Vitaliy Posted November 30, 2017 Author Share Posted November 30, 2017 Bomb ready... 2 Link to comment Share on other sites More sharing options...
Vitaliy Posted December 3, 2017 Author Share Posted December 3, 2017 Added temperature sensors, handle on the hatch and casing 3 Link to comment Share on other sites More sharing options...
Vitaliy Posted December 6, 2017 Author Share Posted December 6, 2017 Assembly the wing dry, in order to check that everything was right... 3 Link to comment Share on other sites More sharing options...
Vitaliy Posted December 8, 2017 Author Share Posted December 8, 2017 Add some ... 1 Link to comment Share on other sites More sharing options...
Vitaliy Posted December 10, 2017 Author Share Posted December 10, 2017 Add airbrake... 1 Link to comment Share on other sites More sharing options...
woody37 Posted December 10, 2017 Share Posted December 10, 2017 Incredible patience and detailing, can’t wait to see some paint over all that detail 1 Link to comment Share on other sites More sharing options...
Vitaliy Posted December 12, 2017 Author Share Posted December 12, 2017 Add LID element (p.e. part ) 1 Link to comment Share on other sites More sharing options...
Vitaliy Posted December 15, 2017 Author Share Posted December 15, 2017 Some work with legs... 1 Link to comment Share on other sites More sharing options...
Vitaliy Posted December 16, 2017 Author Share Posted December 16, 2017 My legs can move... 4 Link to comment Share on other sites More sharing options...
Vitaliy Posted December 20, 2017 Author Share Posted December 20, 2017 Legs are almost ready... 3 Link to comment Share on other sites More sharing options...
Vitaliy Posted December 22, 2017 Author Share Posted December 22, 2017 Add cover on pilon for sniper... 2 Link to comment Share on other sites More sharing options...
Vitaliy Posted January 2, 2018 Author Share Posted January 2, 2018 (edited) Happy New Year my Friends ! Add some work in cocpit area... This area before operation Edited January 2, 2018 by Vitaliy 3 Link to comment Share on other sites More sharing options...
Vitaliy Posted January 5, 2018 Author Share Posted January 5, 2018 Add more detail of intakes... 4 Link to comment Share on other sites More sharing options...
Vitaliy Posted January 9, 2018 Author Share Posted January 9, 2018 Add nose nozzles 1 Link to comment Share on other sites More sharing options...
crushkill Posted January 11, 2018 Share Posted January 11, 2018 Man this bird is gonna be amazing when it’s done! 1 Link to comment Share on other sites More sharing options...
xffw45343tg Posted January 11, 2018 Share Posted January 11, 2018 On 05/01/2018 at 12:32 AM, Vitaliy said: Add more detail of intakes... On your next one Vitaliy , these need to spread away from the centre line as they head downwards; there not actually intakes, but ducts that take the boundary air away from the cockpit sides via thin rectangular spring-loaded doors aft of the seat bulkhead. As the forward speed of the aircraft increases, the suction above the duct exit develops and the doors open against the spring. Air on the inside of the intake is sucked away, cleaning up the airflow to the fan & compressor. If you look a photos of the wheel bay, you can see 3 sides of the base of each duct, bonded to the fuselage side walls. Unless your ducts extend into the wheel bay, no-one (except maybe me) will notice. Kirk PS/ Do you plan to add any cockpit detail? There is a quite prominent "saucepan" (pressure vessel) that sits behind the pilot's left elbow below the low pressure fuel valve and various bits and pieces on the bulkhead that are omitted from the kit. I'm sure you've seen them on your reference photos but shout if I may be of help. 1 Link to comment Share on other sites More sharing options...
matteo44 Posted January 12, 2018 Share Posted January 12, 2018 Well done! Great job 1 Link to comment Share on other sites More sharing options...
Vitaliy Posted January 13, 2018 Author Share Posted January 13, 2018 Thanks my friends - Kirk , Matteo , Crush and ALL who with me in my build WE WIN , THE FORCE BE WITH US ... Link to comment Share on other sites More sharing options...
Vitaliy Posted January 15, 2018 Author Share Posted January 15, 2018 Add more detail... 1 Link to comment Share on other sites More sharing options...
Vitaliy Posted January 16, 2018 Author Share Posted January 16, 2018 More detail... 3 Link to comment Share on other sites More sharing options...
xffw45343tg Posted January 17, 2018 Share Posted January 17, 2018 The canopy guide rail looks very precise. How did you make it? Link to comment Share on other sites More sharing options...
Vitaliy Posted January 17, 2018 Author Share Posted January 17, 2018 Lets see 1.Here's the size 2. Step one 3. Step two 4. Here we go 5 Link to comment Share on other sites More sharing options...
James B Posted January 17, 2018 Share Posted January 17, 2018 Amazing detail. 1 Link to comment Share on other sites More sharing options...
Vitaliy Posted January 18, 2018 Author Share Posted January 18, 2018 Thanks James ! This area is not finished... After glue i continue... Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now