Takom 128mm Flak 40 Zwilling. 1:35

[Shar2]

128mm Flak 40 Zwilling

Takom 1:35

History
The 12.8 cm, (128mm if using si units), FlaK 40 was a German anti-aircraft gun used in World War II. Although it was not produced in great numbers, it was one of the most effective heavy AA guns of its era. Development of the gun began in 1936, with the contract being awarded to Rheinmetall Borsig; the first prototype gun was delivered for testing in late 1937 and completed testing successfully. The gun weighed nearly 12 tonnes in its firing position, with the result that its barrel had to be removed for transport. Limited service testing showed this was impractical, so in 1938 other solutions were considered.

The eventual solution was to simplify the firing platform, based on the assumption it would always be securely bolted into concrete. The total weight of the system reached 26.5 tonnes, making it practically impossible to tow cross-country. In the end this mattered little, since by the time the gun entered production in 1942, it was used in primary static defensive applications. There were four twin mounts on the fortified anti-aircraft Zoo Tower, and they were also on other flak towers protecting Berlin, Hamburg, and Vienna. Approximately 200 were mounted on railcars, providing limited mobility.

The gun fired a 27.9 kg (57.2-pound) shell at 880 m/s (2,890 ft/s) to a maximum ceiling of 14,800 m (48,556 ft). Compared with the 88mm FlaK 18 & 36, the 128mm used a powder charge four times as great which resulted in a shell flight time only one-third as long. This meant that it could be used more accurately against fast moving targets.

The Model
Whilst it is great to see this kit released, I do feel for the resin manufacturers who seem to be having the rug pulled from under them by the injection moulding companies, in that subjects that would normally only be produced in resin are now being picked up to be produced in styrene. Its a great time for the modeller, but I still feel for the cottage industry that has served us well for many years. Still, its a kit Ive always fancied and now we have one that is not only easily accessible, but relatively cheap. The kit comes in quite a large portrait orientated box with an atmospheric depiction of the guns in a night setting. Inside, there are six sprues of light grey styrene, a separate base and turntable, a small sheet of etched bras and a small decal sheet. As there are two guns, the sprues that contain them have been doubled up and the build sequence is the same for both. All the parts are well moulded, with no sign of flash or other imperfections and only a few moulding pips. The kit has been designed so that any ejection pin marks are on the insides/undersides so there is little additional clean up required other than for the sprue gates. The instructions are very clear and easy to read, in fact they have to some of the clearest instructions Ive seen in a while.

Construction begins with the first of the two guns, in particular the slide, which comes in four parts, left and right halves, top panel and a small crosspiece. To this the elevation quadrant is attached, along with two fixing to the rear of the slide underside. The slide piston end cap is then attached to the front, whilst four mount fixings are fitted to the rear. Each barrel is made up of nine parts, with the rear section of the barrel, including the breech and the front section each in two halves split longitudinally. The end of the rifled barrel is sandwiched at the breech end between the two halves and the curved section of breech is attached to the left half. With the front barrel section assembled, the front and rear sections can be joined together via a single piece transition joint. The completed barrel is then slid into the previously assembled slide. The breech is then detailed with the hinged breech block, breech opening ram and associated cogs and the breech block itself, made from three parts. The recuperator tube is now assembled, from two halves to which the end cap, valve and shaft are fitted, this is then fitted to the top of the barrel and connected, by two rods, to the slide. Each of the two trunnions are made up of five parts, to which a pad, and grab handle are fitted to the left hand unit, while the right hand unit is fitted with a four piece elevation gearbox housing. The eight piece shell cradle is then attached to the rear of the slide along with a three piece connecting beam. To the top of the gun there is a complex series of fifteen parts the function of which I cannot find, other than it looks like they make up into something to do with the recoil and spent cartridge removal. The two elevation springs are assembled next, each one consists of the inner shaft, outer cylinder and three piece end cap, and they are then fitted to the underside of the gun.

With both the guns assembled its on to the mounting and the assembly of the middle trunnion mount, which consists of five parts. This is followed by the upper gun mounting base unit which consists of a single piece base, to which the elevation shafts, with added cogs and poly caps are fitted after which the shaft cover is attached. At the front of the base are to storage boxes and two cover plates. Before fitting the guns to the base four hinges need to be affixed to the lower ends of the elevation spring tubes, these are not to be glued, only snapped into position. The inside trunnions are then slid into the central trunnion mount and the whole assembled fixed to the base. Each gun is then fitted with what looks like an elevation motor and a fuse setting to the outside trunnion mount panel which are fitted before these assemblies are attached.. Each elevation motor is made up of nine styrene and two PE parts, whilst the fuse setter machines are each made up of sixteen parts.

The lower base unit is fitted with and end plate, on which there is a small three piece platform with associated PE grating. Each side of the base is fitted with the fighting platforms with handrails and inner edge parts plus two four piece tread steps, each with additional PE mesh grating. Each side is fitted with a crew station consisting of a seat, foot pedals and associated support frame, the right hand side station is also fitted with the training gearbox casing and control wheel. With all the platforms attached the lower base unit is attached to the underside of the upper base section. The modeller is given a choice on how to mount the zwilling, either on the hexagonal base, via a small turntable, for a fixed gun battery, or a smaller round base, also via the small turntable, which can be used on a flatbed rail wagon or the like. Takom do provide a couple of shells to display with the guns, but, unfortunately no crew.

Decals
The small decal sheet has markings for three guns although none are exactly covered in them with just the Hamburg gun being provided with anything different such as the kill markings on the barrels. They are well printed and quite thin, with little carrier film to worry about. The three options are:-

• G-Tower, Caesar gun position, Tiregarten, (zoo), Berlin 1945 in overall Panzer Grey.
• G-Tower, Anton gun position, Stiftskaserne, Wien, 1945, in Panzer Grey with yellow squiggles all over.
• G-Tower, Caeser gun position, Heiligengeistfeld, Hamburg 1945 in either overall Panzer Grey or overall Olive Green.

Conclusion
As I said at the beginning of this review, I do feel for the Cottage Industry and their fabulous creations, but to actually get a subject like this in injection moulding is quite incredible and something that I never thought would happen. I love big guns so was thrilled to hear of the impending release, and the wait has been worth it. There is nothing to difficult with the build, just a bit repetitive with two of everything except the base. It will certainly look great in any collection. The only downside is that, once again we are given a great gun system, but no crew to man it, perhaps it is here that the resin guys can come to the rescue. Very highly recommended.

Review sample courtesy of
UK Distributors for

[Panzer Vor!!!]

So did the crews paint kill rings on the barrels I wonder ?

[Shar2]

Apparently yes. They are provided on the decal sheet for the Hamburg gun.

[AndyC]

Having been up one of the Flakturm in Vienna...may have to invest. Nice review Dave.

[Arniec]

Now we just need a flaktower to put it on.

Cheers,

[snapper_city]

If only I didn't eat so many burgers at War & Peace I would have come home with one. Ze Germans were knocking them out at a good price also.

[Panzer Vor!!!]

If only I didn't eat so many burgers at War & Peace I would have come home with one. Ze Germans were knocking them out at a good price also.

Im saying nothing buddy im saying nothing

Apparently yes. They are provided on the decal sheet for the Hamburg gun.

Doh Read the review idiot