Jump to content
This site uses cookies! Learn More

This site uses cookies!

You can find a list of those cookies here: mysite.com/cookies

By continuing to use this site, you agree to allow us to store cookies on your computer. :)

Recommended Posts

Having a soft spot for all things Postwar Vickers aircraft, I thought I would try my hand at this Vacform model produced by Gene Hooker of USA, I think originally the moulds may of come from a Travel Agents desk model as the kit is not supplied with any props or wheels, but looking at the plans I have it looks quite accurate.
This shall be a challenge as I intend to have the passenger doors open with scratch built steps, I shall be constructing the front part of the engines and making resin moulds from these, also the Aeroclub props are from the Britannia which will be modified, all the windows and doors will need cutting out, I am thinking of making the windows from clear resin, the only thing I shall need to find is some suitable wheels.
Once I have constructed the basics such as the wings and such I can then add extra detail and start scribing
Hopefully as this will be a challenge it will be painted BEA red square colours.

The 4 photos below were taken from Carlos a memeber on Britmodeller and can be deleted at his request, as I did not take any photos showing how the vacform model looks straight from the box, but gives a good indication on how basic the model is and what work needs to be done to make it acceptable.

VanguardKit_01_zpsf72a92cb.jpg

VanguardKit_02_zps68de80d7.jpg

VanguardKit_03_zps0b6d4799.jpg

VanguardKit_04_zpsf49a54db.jpg

DSCN0256.jpg

DSCN0255.jpg

DSCN0254.jpg

Edited by kev67

Share this post


Link to post
Share on other sites

Looks nice and clean, Was waiting for this thread to appear after seeing your other one! Are these kit's still available?

Share this post


Link to post
Share on other sites

Yeap you can still get these from Gene Hooker

sherwoodchatfield@yahoo.com

I think it cost £40-£50

but you will need to email him he also does the C-133 Cargomaster

Just to add, some of the vacform is very thin, so don't expect Dynvector vacform quality

Share this post


Link to post
Share on other sites

Really looking forwards to this Kev, if it turns out half as good as your Varsity, it'll be a stunner :)

Share this post


Link to post
Share on other sites

put me down as a "subscriber" too Kev

always loved the Vickers propjets

The price would have put me off, couldn't buy many of them on my pension, but I'll see how yours comes along

I like where you are with this

And I'm also a fan of the Red Square BEA livery :thumbsup:

win win

Share this post


Link to post
Share on other sites

Would anyone have any spare Lockheed Orion wheels, I have heard that these are similar in size to the Vanguards, I will measure the ones on the plans to see what size they are in mm first

Share this post


Link to post
Share on other sites

Looks a challenge, but you're well-qualified to take it on! Good luck...

Share this post


Link to post
Share on other sites

Working at a snails pace with this, cut the front passenger door out, also added some strengthening to the wings, with some cut plastic and a brass metal bar to stop any wing drooping,
emailed Brooklands yesterday, as I was not sure if both passenger doors on that side of the aircraft are the same width, but they emailed me back and said they were

DSCN0708.jpg

DSCN0710.jpg

Edited by kev67

Share this post


Link to post
Share on other sites

Hi Jessica, the kit only has basic decals for the BEA aircraft, but I think you can ask for Air Canada but you may find they are not all that good anway

Share this post


Link to post
Share on other sites

I have decided to make this particular aircraft G-APEP as I believe this is the one that is at Brooklands
I have also progressed more with the model as I have cut out all the oval windows and added the frame work for the pilots windows, still need to cut out the cargo doors as these will be opened, not worth showing any photos but will do when I can show more progression, both wings have also been done but need to do the centre section and make a spar for the wings, I will build a template to make sure the wings are at the correct angle. Once I am happy with all this I can then concentrate on scratch building the interior, having a go at resin casting as all the seats will be made, but I will not go to mad on the interior as most will not be seen but as the windows are quite large I think its best to show that there are seats inside.

5485494979_9b68949e44_b.jpg

Share this post


Link to post
Share on other sites

Hi Kev, My dear friend and work colleague who sadly died several years ago worked in the old drawing office where the Vanguard was produced and he always raved about it. I built him the old Airfix kit which took pride of place on his desk. Keep up the good work on this truly beautiful aircraft....

Brian.

Share this post


Link to post
Share on other sites

Hi Brian

Thanks for the comment, I have been told by a number of people that it was a noisy beast as well, would like to go to Brooklands when they start the engines up, if they still do that is.

This is going to be a long build, and I am not the quickest at building models its really only when I can get the time, but as i only concentrate on one model at a time, I am hoping that I shall see it to the finish line, there is going to be some modeling skills I have not done before, especially resin castings as the engines wheels and seats are going to be cast in resin and the windows are going to be clear resin.

Share this post


Link to post
Share on other sites

Not much to show,but it does show that I have cut the windows and doors out plus the cargo doors. Just got back from Brooklands, Weybridge, taking loads more photos and measuring some stuff on the Vanguard, got to chat with a pilot who used to fly the Vanguard as well.

DSCN0738_zps5ad5dd6d.jpg

Share this post


Link to post
Share on other sites

Great job on the cut outs kev! About 1959 i can remember the prototype Vanguard flying over our house ,1000 ft or less, in Feltham on finals to heathrow,not BEA colours BTW.I was about 4 or 5,my dad told me what it was!

Share this post


Link to post
Share on other sites

Cheers, the oval shapes of the windows were not to bad as I used the decals as a template and just cut out near to the decal and then sanded theses to shape, there are a few that need adjustments but they are all straight, anyway I have started scratch building of sorts the front part of the engine, this then can be cast in resin for all the front engines

Share this post


Link to post
Share on other sites

Started to try and improve the front of the engines, the photo shows the original vacform part, all I need to do is add some panel lines and some air vents and other small details , the front prop cowling is only there to show the position, this will be a separate cast in resin as well, the props will come from a Super Transell but as they are smaller I shall cut these down to right length.

prop_zpsf428a4e4.jpg

Share this post


Link to post
Share on other sites

Brings back memories... I flew from Jamaica to Toronto on a "Scare Canada" Vanguard, on July 1st 1967. My first overseas trip, 6.5 hr. at 400 mph to Canada!

Tony

Share this post


Link to post
Share on other sites

Fantastic job! I would so like to get one of these kits.

Cheers

John

Share this post


Link to post
Share on other sites

Looking great Kev, looking forward to seeing this progress.

Share this post


Link to post
Share on other sites

Cheers John, I think I posted the email address of the person in the USA who does these

Very slow at the moment, I wish I could build as fast as you Tom, at the moment I am detailing the front landing gear wheel well

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...