Search the Community
Showing results for tags 'RAM Models'.
Found 3 results
A good evening to you all, despite the sad events of today, First of all, a bit about me: From a young age I was first introduced to the RAF Museum at Cosford, I have been there during the construction of the Cold War hangar and although I can't remember it, I presume that I must have been there before the Nimrod (XV249) arrived and I have since become well acquainted with it when they brought it in during 2012. Out of all the exhibits there, the Nimrod is still the one that catches my eye- perhaps it is because of its size or it might be due to the red goose emblem of 51.sqn on its nose! (Pictured) Having gone to Telford in 2015 and having seen an Airfix 1:72 Nimrod kit, I simply couldn't resist! So, without further ado, the following is a quick summary of the kit and modifications: 1:72 Airfix Nimrod kit A set of fabulous decals from RAM Models (more on this later) A really excellent Raven Scale Models lighting kit (again, more on this later) A few scratchbuilt bits and pieces, mainly the "forest" of antennae and pitot tubes. Finished with a combination of Vallejo "Air" paints and some AK Interactive washes. NOTE: THE MODEL I HAVE CREATED IS NOT 100% ACCURATE and the positions of the lights are certainly not accurate! Issues with the kit: The wing-fuselage join was horrendous (although this might be due to the wires of the lighting kit getting caught in the internal structure of the fuselage) and so vast quantities of liquid poly glue were utilised and subsequently sanded down to get a "decent" seam. The wing-tip pods were not suitable for the R.1, these were made from bits of sprue which were sanded down and hollowed out. -This isn't much of an issue with the kit, but an issue nevertheless: trying to get the wiring through the wing structure and into the wing-tip pods was a nightmare, this is not a fault of the Airfix kit or the lighting kit- just a problem with trying to integrate the two. Now, time for some pictures! The superb RAM Models decals for the 51 sqn goose on the nose. And another view of the nose..... You can tell that I love that decal Last one I promise!!! (Note the effective texturing of the goose decal). A nose-on view A view of the wing structure, intakes, wing fuel pods, antennae under the wing, try and ignore the light to the right of the intakes, the hole is to allow a strong beam of light through from the LED A view of the central fuselage section, note the "forest" of antennae The flaps and engine nozzles. And the left side... (The rigging from the fuselage to the tail needs re-tensioning) A close-up of the tail section Excellent decals once again from RAM Models I attempted a moderate level of weathering using an AK Interactive wash From a distance... And underneath... A selection of AK Interactive washes were used for the landing gear bays, also note the antennae just in front of the pylon and another one coming out from the rear of the wing-tip pod (this one somehow survived without breaking off!) One final shot before I demonstrate the lights. As mentioned previously, I used the lighting kit from Raven Scale Models, the image below shows the underside of the Nimrod- note the position of the bomb-bay panel. Now you see it... Now you don't! -The wiring was redirected into the bomb bay area, where the battery holder is located and where the switch (silver coloured thin tube) is activated from. It lives! (sort of) Demonstrating the landing lights- I haven't added lights to the nose or to the inner wing-mounted landing lights, purely due to the fact that using fibre optics would ultimately reduce the intensity of light coming from the lights that are currently present, I would prefer there to be two bright lights compared to 5 dim lights. They're quite bright! The placement is pure fiction, but there is one red flashing light (pictured) and two flashing strobe lights Furthermore, there is one light in each wing tip (red and green), again their placement is somewhat fictional; i've been told that they should be swapped over (I'll be damned if I'm changing their position now!) And that, alas, is that. Thanks for having a look, she'll now be fitted with wire and hung from the ceiling- flying alongside the Shackleton, the Nimrod MR2's predecessor and stablemate in the ASW role during the Cold War. Perhaps I'll get round to doing an MR2 one day.... But for now, thank you and have a good evening- my best wishes, especially to members in Belgium. ;( Sam
RAM Models is to release on February 29th, 2016, 1/72nd Vickers VC-10 C.1/C.1K vacuform kits. Source: http://www.rammodels.co.uk/index.php/cPath/65 V.P.
Hi All I just got Ram models new decals through the post today . First impressions are good , the decals seem well printed and of good quality there is also some very nice artwork as well . This sheet well covers some of the early Phantoms in RN service , I hope there may be more to follow maybe some late RN aircraft " cross deck graffiti and the like ", some RAF camo aircraft as well as three tone gray . I really need to model a gray 56sqn aircraft with red tail and shark teeth . Regards Glenn.