Search the Community
Showing results for tags 'Petes Hangar'.
Found 1 result
Navy Bird posted a topic in F-111 STGBAll right then, time to get started! My project for this group build is the Grumman/General Dynamics F-111B. I suspect that everyone knows the story of this aircraft and its development, but if not I'll direct you to the mother-lode of F-111B information later on in this post. My initial idea is to model one of the Phoenix missile test aircraft, and BuNo 151972 seems a good candidate. This, of course, will be a conversion and my base kit will be the Hasegawa 1:72 RAAF F-111C/G. This is a great kit, and contains all necessary parts to build either the C or G model. The G is essentially the same as the FB-111 as you know. Let's see what we get (and it's so much that it's difficult to close the box without squeezing the contents). First, the specific kit I'm using: Inside we find a lot of styrene! This next photo may look like two copies of the same sprue, but they are different - one is sprue C and the other sprue D. The difference is primarily with respect to the intakes as the F-111C and G had variations in this area (Triple Plow I vs. Triple Plow II). Since 151972 did not have either of these intakes, I will be modifying the Triple Plow I. And the rest: And finally two of these babies: I've acquired several bits of aftermarket goodies to help with this conversion, starting with the set from Pete's Hangar which unfortunately is no longer available. My understanding is that this set has a few problems, but they don't look to be insurmountable. Apparently, the shape of the nose, and its demarcation with the fuselage, is not quite right, but that's why they call it modelling. Some additional decal sheets that may be of help - the sheet from Pete's Hangar is also pictured here, but the other two sheets are from Microscale and are quite old. 72-132 includes the markings for 151972, and 72-452 includes stenciling for the early models of the F-111. Also shown here is the sheet from the kit, not sure if any of this will be used. The Phoenix testing logo is different between the Microscale and Pete's sheets, and based on photographs it looks like Microscale is better (for instance, Pete's omits the fire that the Phoenix bird is emerging from, the USMC globe and USN anchor). I hope those old Microscale sheets are still good! Some additional aftermarket that may be used. Obviously, not all of the photoetch for the F-111D/F is appropriate, but some of it may be useful. We'll see. The masks are fine, but what's this with the ejection seats for a B-57 Canberra? The F-111 had a ejection capsule! Well, yes it did, after a fashion. However, the first three F-111B prototypes, including 151972, did not have the capsule, and were instead fitted with Douglas Escapac ejection seats. According to the Ejection Site, they were model 1C. The resin seats from Pavla are models 1C-6, and have the right basic shape. But I suspect they will need some alteration or enhancement before the end of the day. Finally, the old Revell kit from 1966 will also be used, as it contains a lot of parts that will help, like the knife edge boat tail, aft fuselage bullet fairings (speed bumps as they were called), etc. I picked this up at a model show, and although it's been started (the B/C/FB long wing tips have been glued to the wings) that won't be a problem as I won't be using them. This is one of the few kits produced which claimed to be a B model. Like a lot of kits from the 60s, this one came out while the aircraft was still being developed, and contains several issues. But I think it will come in handy nonetheless. The loose parts, rolling around in the box: And the ones still clinging to the runners: Also in the box were these four pylons, which I suspect are from an F/A-18. But they have a shape resemblance (kind of) to the pylons used by 151972 for the Phoenix missiles. I will be checking if they are close to being the right size, and might work for the model. Again, we'll see. Perhaps they can be modified, maybe not. But it was nice of the chap who sold this to me to include them! The Phoenix missiles will probably be sourced from a Hasegawa F-14A kit, but will need some mods to represent the missiles used in the F-111B test program. Now, about that mother-lode. If you're going to build an F-111B, you simply have to have this monograph: Tommy is the F-111B subject matter expert, and he contributes regularly to Britmodeller. I expect he will show up here to keep me on the straight and moral path. If you follow this link, you'll go to Tommy's blog where he has posted several links to articles that concern the F-111B. There are also instructions for how to obtain the amendments and errata for the F-111B monograph. All of this material taken together remains the prime reference for this much-maligned bird. Cheers, Bill