Search the Community
Showing results for tags 'NCC1701'.
Found 1 result
Hi all, I've been here a few weeks now and though it was about time I showed you what I'm up to. I've very fond memories of watching Star Trek (TOS) as a kid in the 80's with my dad and my brother and it's one of the few things that has really stuck with me through changing times. The Enterprise itself I find mesmerising, it's graceful and each part of the ship has a clear purpose, a design classic and I love it. My favourite itteration has to be the refit, which I hope to build at some point in the future So, I got in to modelling because I wanted a decent model Enterprise, I've had a few very small die-cast models but they are always lacking something. I found the Revell kit online and decided that I'd build my own, LED lights and all. Now I've well and truly got the modelling bug, I've bought the Star Trek Starship Voyager for my next model, I've built a small Star Destroyer and plan to build models from Battlestar and other Star Trek models Here's some photos that I took while building my Enterprise, I wasnt originally planning on posting them online but then I found this place, so here it goes! 1. What a great start, I ruined my first model! I wanted to light my model with LEDs, so it had to be light-proofed. So the insides of the model had a coat of adhesion promoter, followed by black, then a silver or while coat would be painted to make it reflective. I was watching lots of Boyd's Trekworks Youtube videos for info and he used a heat gun on a gentle heat to aid the drying process.... I'll never do that again, my model melted You can see the plastic deformation from the heat in this image. It also shows my initial plan for lighting, which was to cover all windows with grease-proof paper, which diffuses the light, then placing LED's around the ship to light them up. 2. Saucer section interior is about ready So after buys a replacement model I started again, with a few important lessons learned This image shows the insides of the saucer section, painted and with the windows covered. I used 'Revell Contacta Liquid Special' to glue the clear windows in place, and to glue the greese-proof paper in place. The secondary hull, again with the inside prepared for lighting, it's had a black coat followed by a light coat to refelct the light. By this time I'd also started experimenting with LEDs, the breadboard in this photo had a 555 Timer chip and a 4017 Decade counter, they'll be used for the rotating lights of the Warp Nacells and the blinking navigation lights. 4.Let there be light! Not sure of the best positioning and arrangement of LEDs I just dove in with something that looked like it would give good coverage. I know some people use fewer but brighter LEDs, and some use LED tape/strips, which I might look at using in the future. Each LED has a resistor attached, and they're all in parallel, so if one should fail the others will continue to work. 5. Glue. After lighting the secondary hull in a similar way I was ready to glue a few parts together. Which I was pretty worried about as I considered it opportunity to ruin yet another model. I used Revel Contacta Professional glue and found my fears were unfounded, thankfully 6. Circuits To light this model I would need to build some circuits to handle the navigation lights and the rotating buzzard collector effects. So I bought the relevant gear from Maplin (I now use RS instead) and designed a few circuits in Pad2Pad, which is excellent free circuit design software. The first completed circuit was for the navigation lights, I was initially planning to put it inside the model but then decided I would fit it in the stand instead. 7. Warp Nacell Test #1 You saw my breadboard with a few components in an earlier photo. This is basically how the Buzzard Collector effect works on my model, The red, orange and green LEDs are aranged in a circle and give the impression of rotation. 8.Warp Nacell Circuit fitting After designing my Warp Nacell circuit in Pad2Pad, I printed it off, cut it out and placed it in it's intended final position to make sure it would fit. The circular plastic piece has holes drilled in it to receive the LEDs, 12 of them (for a single Nacell). 9. Assembled Warp Nacell Board After building the warp nacell board I fit it in place. Now you can also see how the LEDs sit. It's a pretty tight space so I was pleased that everything went in with no problems In the video below, the middle light isnt connected to any power, it will eventually be 'always-on' to provide a steady red glow. The camera doesnt really do the below any justice. 10. Closed up my first Warp Necell - and made my second big mistake It's amazing isnt it that you can do something, then the instant you finish you realise you've done it wrong. I guess it's not really that big a deal, the model isn't completely accurate anyway and I'd already decided that I would'nt worry about that this time. But this mistake was easily avoidably, yet at the crutial point I... put the wrong circuit in the wrong nacell, so the buzzard collectors now spin in the wrong direction. Only a Trek fan would notice, but it's annoying all the same. Still, after much grumpiness I think I can live with it. 11. Connecting the Pylons and the Seconday Hull. I'd already glued the warp nacells to the support pylons and let those set, I'd also done some work on removing the seams on all the parts glued so far. Now it was time to connect the wiring up and glue them to the secondary hull. With the wiring connected and the pylons glued on to the secondary hull, it looked like the area would be under a fair bit of stress, so I stuck a clamp in place to hold things together while they set. 12. Windows, I hate Windows I bought some masking fluid so that I could mask the windows, but found it to be far to imprecise and the results (of tests I did on my melted saucer section) were pretty messy. So after getting some advice right here on Britmodeller (thanks guys, you know who you are) I settled on masking the windows with masking tape. I used a scalpal to cut small rectangles working on one at a time. It took ages. I have used the masking fluid on a few of the larger clear pieces, but I'm still not impressed with the result, maybe I just need more practice with it! 13. All Masked, Time for the Primer With all the clear parts masked I bought myself a 'lazy suzan' and gave the entire ship a coat of Hycote Adhesion Promoter and then a nice coat of Hycote grey primer. No way was I going anywhere near this thing with a heat gun The wires you see here will eventually be fed through the stand in to the base. I found the Hycote cans give excellent fast coverage, pretty cheep too. 14. Base Color With the primer dry it was time to start mixing colours (as per the model instructions) and giving it some proper color. I used a 'Sparmax Arism Mini' Airbrush to spray the model, with Revel Aqua Color paints. I found that thinning the paint 2-parts paint to 1-part thinner worked pretty well. I'd aslo sprayed the deflector dish, I love that copper colour and started giving the warp nacell and impulse engines some colour. I was having trouble cutting the masking tape perfectly to cover the inside of the impulse engines, so decided to try the masking fluid. The result was not great but I think It'll look fine if I touch it up with a brush. So, that's my model so far. It's the first model I've ever build and while I've found it quite challenging I've really enjoyed it and plan to do many more in the future. I'll post more photos and videos as I make more progress. And thanks to everyone here for accepting me in to the site and giving me some great tips! Cheers