Search the Community

FWD Type B 3 ton truck (35655) 1:35 ICM via Hannants Built by the Four Wheel Drive (FWD) company, this was a very early truck used by the military of Britain and the US during WWI, beginning in 1915 with a small order from the British Army. It was full of curious technology from a modern standpoint, but then vehicles of this type were still in their infancy, so that’s hardly surprising that there were a few dead-ends. It was originally supplied with solid tyres and the front wheels had a strange toed-in look due to the suspension geometry set up to give a light steering load. Its T-head engine produced a monstrous 36bhp for rice-pudding skin removal, and it could be connected to all four wheels or either front or rear in the event of necessity or damage to either drive-shaft. It also had a distinctive pig-nosed front due to the fact that the engine was mounted below the cab, with only the radiator housed in the front and precious little (read: none) cover for the driver and crew. Over 12,000 were made up until the end of WWI, with them finding a ready market in the post-war period in the civilian sector, sometimes with pneumatic tyres added to improve the ride quality. The Kit This is a new tooling from ICM, widening their WWI vehicle range again. Arriving in their usual captive inner lidded box, there are four sprues in grey styrene plus a tiny clear sprue, a similarly small decal sheet and the instruction booklet with colour cover and spot-colour inside. It benefits from the same attention to detail that they have lavished on their other WWI kits and you get a full model that includes engine and chassis details not supplied in some other manufacturer’s kits. Construction begins with the double ladder chassis with suspension and cross-rails included and adding the axles, brakes and drive-shafts, most of which are broadly familiar but a little odd looking into the bargain. The larger rails of the chassis denote the rear of the vehicle, and at the front the steering linkage is added before the wheels are made up from three layers each plus hubcap, then fitted to each corner of the vehicle. The radiator core has its sides fitted then it is dropped into the front of the chassis, then joined by the peculiar engine, which is very well detailed with almost 30 parts devoted to its construction. Once it is painted and in place the exhaust is threaded through the chassis and attached to the manifold outlets, with the diagram helpfully ghosting one of the wheels to improve your view. Power transfer boxes are suspended from the underside of the chassis rails with more drive-shafts, then up at the front the chassis is widened by adding tread-plated “shelves” to the sides before beginning work on the cab and snub-nosed bonnet. This assembly also includes an engine cover that ends up with the crew sitting on it and in the gap between the cowling and radiator the crew have a small footwell with driver controls and a fire extinguisher present, louvered side panels to the cowling and cooling fan for the radiator that is surrounded by a shaped cowling that plugs into the back of the radiator later. The fuel tank is made up from four sections plus two supports, then the lovely deeply upholstered crew sofa is put together with moulded-in buttons giving it a Victorian drawing room feel. The steering wheel and control levers are added to the sides of the cowling, then the seat is dropped on top with a nice cosy fuel tank right behind it. The perfect cab. Exposed to the elements, high up and with extra heating in the summer, plus a big flammable tank right behind your seat. Awesome! The old-skool railway-style front lamps and U-mounted searchlight are put in place on the front and stowage is placed on the left foot-plate, presumably tied down so you don’t lose it on the corners, and the hand-crank starter can optionally be inserted into a socket on the front chassis rail if you wish. The 3-ton load bed begins with the floor and has five cross-beams slotted into position underneath, a front panel and two side panels that have braces added down the sides before they are installed, located on the pins on the end of each cross-beam. The tail gate is made up from frame and panel parts, then two stowage boxes are built up and fitted to the underside front of the bed, which is then mated with the chassis on a number of tabs and slots. You can model your truck with the tilt stowed or in place, with the former having five hoops fitted down the side panels to complete the assembly. For the covered bed there are five parts to make up the canvas tilt with some nice sag moulded-in. Hide the seams and paint it accordingly and you’ll end up with a believable looking tilt. That’s it. You’ve finished. Markings There are two decal options on the tiny sheet with just stencils on the sides to differentiate them from each other as they are both painted olive green. The few decals on the sheet are all white, so there’s no worries about registration, but colour density and sharpness are good. Conclusion An early truck that became a staple of the battlefield in WWI and beyond in injection moulded styrene with plenty of detail. It’s a nice kit and great for WWI military modellers. Highly recommended. Available in the UK from importers H G Hannants Ltd. Review sample courtesy of