Search the Community

Hi all Can anyone recommend any suitable figures for a Chinese Type 59 tank, late 80s? Regards Mick

Chinese Type 59 Medium Tank MiniArt 1:35 Obviously, the Type 59 was a faithful reproduction of the Soviet Type 54A, internally and externally, although the Chinese did make some modifications. It was simplified in design, without the characteristic IR searchlight and main gun stabilization system. The hull was welded with some 99 mm of armour thickness on fht front slope, and 100 mm for the front turret armour, which had the characteristic decrease in thickness from the base to the top, according to ballistic penetration calculations. The turret floor was non-rotating. The driver, loader, commander and gunner positions were unchanged. Main armament was the 100 mm Type 59 tank gun, a copy of the original D-10TG with its characteristic muzzle fume extractor, with 34 rounds in store, mainly into the hull. Secondary armament comprised a coaxial Type 59T 7.62 mm machine gun, a bow MG manned by the driver from inside the central glacis (3500 rounds in store), and the anti-aircraft heavy machine gun Type 54 12.7 mm over the loader’s hatch, apparently also a copy of the DShKM, with 200 rounds in store. The engine was the Model 12150L V-12 liquid cooled diesel, giving 520 hp at 2000 rpm. The overall weight was also equivalent to the T-54A and road range was about 600 kilometres, with the rear external fuel tanks. These tanks, were upgraded several times throughout their career which lasted from 1959 till 1985. The Model Having reviewed the T-54A here MiniArt are now releasing the various derivatives and those used by other countries. As with earlier kits there are a lot of similarities but quite a few new parts as well. Although not having as many sprues as those kits with interiors, the box is still stuffed full of sprues. On opening you are greeted by a mass of sprues, many of them quite small because of the tooling's modular nature, with quite a few parts going unused for this boxing. The mass of sprues fill up just about all the space in the box, leaving only room for air between the sprues, anyone familiar with the old Krypton Factor will realise getting all this back in the box is one of life’s little challenges! Construction is almost identical to the earlier releases, The lower hull then fitted out with a multitude of parts that include the torsion beam suspension, multi part axles, gearbox covers, and interior escape hatch plus PE beam covers. The upper glacis plate is then fitted as are the three piece road wheels, drive sprocket and idlers. The turret ring assembly is the attached, followed by the rear bulkhead, each fitted with more detail parts. The engine deck is then built up and the separate hatches are able to be posed open or closed as per the modellers’ wishes, but since this kit doesn’t have an interior there seems little point unless you have purchased the separate engine kit which is available. The deck is topped off with PE grilles in their frames and the large hinge for the main hatch. The tracks are of individual link type, with ninety links per side, and it will be a case of assembling it like a link and length style, gluing each link together before draping them over the road wheels. The fenders are fitted with stowage boxes, fuel tanks and spare track links plus front and rear mudguards before being glued into position. The two fuel drums mounted to the rear of the tank are assembled and glued into their mounting frames, as is the unditching beam and the pipework for the fender fuel tanks. The turret roof comes complete with all the periscopes and hatch details for the commander and gunner positions, a highly detailed Dushka (DsHK) 14.5mm heavy machine gun, consisting of twenty nine parts, and rolled up tarpaulin. The single piece main barrel is glued into the breech, and fitted with the mantlet cover. There aren’t as many grab handles fitted to the outside of the turret on this version, or brackets and clamps. Finally the driver's wet weather cover, that fits over his hatch can be posed stowed or in place. If you are stowing it, there are some PE straps to tie things down on the bustle. The turret assembly is then fitted to the hull, completing the build. Decals The decal sheet gives the modeller seven options. The decals are beautifully printed, are clear and in good register with a slightly matt finish. The options are:- Type 59, No.308 of the Chinese People’s Liberation Army currently still in service. Type 59, of the Armed Forces of the Islamic Republic of Iran, used during the Iran – Iraq war in the early 1980’s Type 59, of the Albanian Army, used on the border area with Kosovo, April 1999 Type 59, No.503 of the Chinese People’s Liberation Army currently still in service. Type 59, No.408 of the Chinese People’s Liberation Army currently still in service. Type 59, No.852 of the 201st tank regiment, Viet Cong, on the 17th Parallel, March 1972 Type 59, No.808, of the 108th Tank Regiment, 43rd Army Corps of the Chinese People’s Liberation Army during the the Sino-Vietnamese War, February 1979. Conclusion MiniArt’s march through the various T-54 and T-55 variants continues apace with this release. Being without the mega amount of parts found in the interior kits, this is definitely more suited to the intermediate modeller, or those who just don’t want interiors to their models. It’s still a great looking kit and with the decal options available for a number of different coutries something different for the collection. Review sample courtesy of Miniart - Distibuted in the UK By Creative Models

Chinese PLA Type 59 130mm Towed Field Gun Trumpeter 1:35 History The PLA Type 59 is a licensed built copy of the Soviet M-46 gun which was developed from the M-36 130 mm naval gun used on ships and for coast defence. It is a true gun, being unable to fire much above 45° and having a long barrel and a single propelling charge. It has a 52 calibre barrel with a tied jaw horizontal sliding block breach and ‘pepperpot’ muzzle brake. The latter is not notably efficient, but subjective reports suggest that it is quite effective in reducing muzzle flash. The hydro-pneumatic recoil system comprises a buffer below the barrel and a recuperator above the barrel. The long barrel enables a substantial propelling charge by providing more length in which to achieve ‘all-burnt’ and hence projectile acceleration space and thus achieve its 930 m/s muzzle velocity. The barrel is mounted on a split-trail carriage, with deep box section trails and foam filled road wheels on the ground when firing and 50° of top traverse. The small shield protects little more than the sights, possible including from the effects of muzzle blast, and some protection from machine gun fire in anti-tank engagements. The gun has long and robust trails to provide stability when firing, a large detachable spade is fitted to the end of each when the gun is brought into action. Non-reciprocating sights are standard Soviet pattern, designed for one-man laying. Included are a direct fire anti-tank telescope, a panoramic periscopic indirect-fire sight (a dial sight) in a reciprocating mounting, an angle of sight scale, and a range drum engraved with the range (distance) scale, coupled to a mounted elevation levelling bubble. The range drum enables the standard Soviet technique of semi-direct fire when the piece is laid visually on the target and the range set on the range drum. An APN-3 was later provided for direct fire at night in place of the day telescope. For travel, the gun is towed via a two-wheeled limber fitted to the end of the closed trails, with the spades removed and carried on each trail. Simple jacks on the trails just behind the main wheels are used to lift and support the closed trails so that the limber can be connected. The barrel and recuperator are pulled back between the closed trails and locked in a travelling position. There is a large bicycle chain arrangement on the right trail for this, and a compressed air cylinder, charged by the gun firing, is used to bring the barrel forward when the gun is brought back into action. It takes about four minutes to bring the gun into action; the normal detachment is eight strong. Propelling charges are in metal cartridge cases and loaded separately from the projectile. Projectiles originally included HE fragmentation, Armour Piercing solid shot, and smoke, illuminating and chemical. HE shells weigh some 33 kg. Illuminating shells have a substantially lower muzzle velocity. APHE and extended range shells were introduced later. Maximum rate of fire is probably 6-7 rounds/minute, and about 70 rounds/hour. The Model The kit comes in Trumpeters standard top opening, and quite attractive box, with an artistic representation of the gun in action. Inside there are eight sprues of beige coloured styrene, almost the colour of a Caramac candy bar. There are also a set of two rubber tyres, two separate trail legs, a small etch sheet and a small decal sheet. The parts are really well moulded with no flash and only a few moulding pips needing removal. Although not to everyones taste, the rubber tyres are nicely done with finely moulded details on both the tread and the sidewalls. The build begins with the heart of the mount, the central casting, onto which the two axles, base, ancillary hydraulic unit, various hooks, handles, and other fittings attached to it. On the underside the turntable is attached to the casting by a large pivot and a couple of connecting arms with the turntable also being fitted with a couple of handles. This assembly is put to one side whilst the gun is put together. The rear of the barrel is assembled from upper and lower halves and fitted with the elevating ratchet mechanism, to this the three piece breech block is assembled and slid into the breech part, which is then completed with the addition of three outer plates before being attached to the rear barrel section. The recuperator mounts are then fitted to the front of the breech and the rear of the barrel. Each of the two recuperators are then attached to their mounts, followed by the breech handle and protective plate. Next up is the complex sight, which is made up of no less than thirteen parts. This is then attached to the left side of the breech/rear barrel assembly along with the recuperators protective top cover and left hand breech panel. The barrel, which seems disproportionally long, is also provided in upper and lower halves, to which the two part muzzle brake is attached before the barrel is fitted to the breech assembly. Turning the barrel assembly upside down the two elevation springs are attached, before turning the barrel right side up and fitting the trunnion with moulded on sprocket, and trunnion mounts which are in turn attached to the central casting and fitted out with numerous unidentifiable fixtures and fittings. The two, two piece trails are fitted out with barrel cleaning rods, pioneer tools, clamps, hooks, handles and the five piece jockey wheels and, on the right hand trail the towing eye. The trails are then fitted with their top plate so that the two parts slide over the top and bottom pivots on the central casting. The two spades that fit to the rear of the trails are fitted with a selection of handles and attachments with the option of positioning them in the traveling position. The wheels are then assembled from the rubber tyres plus inner and outer hubs, (the inner hubs are fitted with a brake accumulators, pipework and linkages), before being fitted to the axles. Before fitting the two splinter shields, of which there are optional styles to choose from, they need to be fitted with the binocular and map boxes, support arms, sighting/viewing port doors and three PE handles, before being attached to he front of the gun mount.Finally the elevation wheel is attached, along with a couple of locking handles at the end of the trails, completing the build. If you wish to build this kit as part of a diorama Trumpeter have included a small fret which contains a wooden shell box with separate lid and PE corner protectors, plus a separate shell and charge case The small decal sheet provides just two decals, one showing the elevation/range chart is positioned on the left hand side of the breech, whilst the other appears to show the gun arrangement and is positioned near the top of the right hand splinter shield. Conclusion I really like these field guns from Trumpeter and this one is just great. There is plenty of detail and from the quick bit of research it looks pretty accurate. Whether it’s used in firing or travel mode this will look great in a diorama although it will need a suitable tractor to go with it. The only disappointment is that the gun crew aren’t included, although I’m sure Trumpeter will release a separate set of troops at some point. Recommended. Review sample courtesy of UK Distributors for