Search the Community
Showing results for tags 'Edurard'.
Hello all. This kit was a "Bucket List" I have to do a Zoukei-Mura kit. I started with the radial engine about 2 years ago, but it went back in to my cabinet of ongoing projects. This week I found out a Campaign is running with the subject Radial Engines. Still waiting for approval of a started kit for that campaign, I might as well do the build blog over here on Britmodeller.com. Should be fun. The Magnificent Mitsubishi Kasei Engine Type 23kou Zoukei-Mura let you build a plane just a little different from the others you build. They have a 'Concept' for that. Reading the manual before you start is more than needed with good information, some history, etc. The kit is not over engineered, but construction is like the real deal and it works only if you follow up instructions very precise. The Office... A Sunday morning build. Fit is unbelievable good. The details go under the floor and all will be connected. For this kit I have an Eduard PE set. Except for the IP, (my eye sight is too bad for painting that), I will not need the rest of the PE. Detail is just very good. would be a Big Sin to cut away the pretty levers and switches. Next will be the wing, landing gear and radio. So far so good. It was a nice Sunday, little bit of this and a little bit of that. All the best and until next time. Robert Jan
Focke-Wulf Fw.190A-4 Weekend (84121) 1:48 Eduard Introduced in 1941 to combat the ever-improving Spitfire, the Fw.190 was intended to supplant the Bf.109 if it reached a plateau in development, or run alongside it as a stablemate. Its powerful twin-bank radial engine was installed with a close-fitting cowling and was initially equipped with an oversized, ducted prop-spinner to keep the engine cool, which was discarded early in development in favour of a fan that ran on the prop's drive-shaft to push air through the cylinder heads, which also facilitated oil cooling. It was also given a wide-track landing gear, which reduced the likelihood of a nose-over, a problem afflicting both the 109 and Spitfire, due to their narrow track and poor forward visibility. When it first encountered Spitfires, it gave the Allied pilots a shock, as they were expecting 109s, not these agile little aircraft. It caused an frenzy of development at Supermarine, which was just part of the leapfrog games played on both sides throughout the conflict. The initial A-1 production version was equipped with a BMW 801 engine, and by the time the A-4 was signed off, it had two 7.92mm guns in the cowling, and a pair of 20mm MG151 cannons in the wing root, all of which were synchronised with the prop's motion, in turn mated to a more powerful version of the BMW engine. There were a number of equipment fits used to give the Würger (Shrike) additional weapons and capabilities, including a pressurised cockpit, rocket tubes and reconnaissance cameras. The A-4 also saw limited service as the F-1 in a ground-attack role, and was eventually replaced by the A-5, which moved the centre-of-gravity forward to accommodate the larger load it was capable of carrying. The Kit Since Eduard started reboxing their new kits the A-4 doesn't seem to have been available in a weekend boxing on its own until now. These new kits from Eduard are top notch in all respects. Inside are five grey/blue sprues, one clear, two decal sheets and the instruction/painting guide in glossy colour printing. Due to the pick-n-mix nature of the sprues there will be a fair quantity of spares left after construction, which are marked on the diagrams with a pale blue overprinting. Construction starts in the cockpit. The tub includes the sharply pointed rear deck, to which you add the rear bulkheads, control column, seat, rudder pedals, and sundry other parts in styrene. In order to close up the fuselage the cockpit assembly is inserted along with a bulkhead that closes up the front of the tub, two exhaust inserts in the cowling, and the engine assembly, which is only an approximation of the front row of cylinders, plus the reduction gear, as not much will be seen once the cowling is in place. The lower wings are full width, and have a spar fitted that runs to the ends of the gear bays, with detail on the face visible through the apertures. This is augmented by the wheel trays, various ribs and the cannon barrels that protrude through, with the upper wings added after painting of the bay roof detail that is etched into their underside. The completed wing assembly is then offered up to the fuselage, and the missing sections of the cowling with exhaust stubs, gun barrels and troughs are added to the top and bottom of the nose. The two-piece ring finishes the front cowling, and the flying surfaces are glued into to place, including separate rudder and ailerons, and fixed elevators. Two types of tyres are provided for the main gear, which have separate hubs, and fit onto the peg on the ends of the strut, with separate oleo-scissors and captive bay door parts. The retraction gear is installed on the inner side of the leg, and the centre doors fit to the central bar that splits the bays. The tail wheel slots into the rear, crew step, gun barrels and pitot probes are installed, then the three-bladed paddle prop is completed with spinner and fan behind it, with a peg at the rear fitting into a corresponding hole in the engine front. Different open and closed canopies are provided, and are outfitted with head armour before being added to the airframe along with the windscreen part. If you are rigging the aerial wire to the tail, remember that if you pose the canopy open, the wire can appear relaxed, although many photos also show it taut, so check your references. Markings This weekend edition gives you two decal options, from the box you can build one of the following: Fw 190A-4 1/48 - W. Nr. 5533, flown by Oblt. Wolfgang Leonhardt, CO of 6./JG 1, Woensdrecht, the Netherlands, October 1942 2 / 2 Fw 190A-4 1/48 - W. Nr. 583, flown by Uffz. Karl Knespel, 1./JG 1, Deelen, the Netherlands, April 1943 All the decals are printed in house, have good registration, colour density and sharpness, with a thin matt carrier film cut close to the edge of the printing. The stencils are catered for on a separate sheet, with a page of the instructions devoted to their placement, away from the markings options to avoid clutter. As always with Eduard, the Swastikas are provided on one cut-off corner of the sheet, and in two parts on the body of the sheet to comply with local regulations regarding this contentious symbol. Conclusion The surface detail on the kit is excellent, with lines of finely engraved rivets adding to the visual appeal (yes, we know rivets aren't holes, but this technique works for most of us though!). The weekend edition brings this excellent kit out at a good price point. Very highly recommended. Review sample courtesy of
Fokker Dr.1 Engine 1:72 Eduard To mark the re-release of Eduard's nifty little Fokker Dr.1 (reviewed here) the Czech firm have bestowed upon us a brand new resin engine. Included in the now-familiar 'Brassin' blister pack are just three resin parts and a tiny fret of etched metal which holds the ignition wiring. The resin parts are beautifully cast and tick all the boxes in terms of fulfilling the functions of an aftermarket upgrade. Recommended. Review sample courtesy of