Search the Community

Now that I have got my Defiant completed I'm trying to tackle a few models I've had on the go for a while and this Hawker Hunter has been crying for attention for a while now so I decided to crack on with it. Revell 1:32 Hawker Hunter by Marks CVS, on Flickr I purchased it one Christmas from Modelzone for about £10 in the sale and is one of the best bargains I ever had and is definitely one of Revell's best kits in my opinion. I ended up getting the True Details cockpit for this one. In all honesty I don't think the cockpit tub and instrument panel offer much difference over the kit parts. Especially as everything is black inside the cockpit. Where this set adds value to the model is in the ejection seat. It is a stunning piece of resin and to date is probably the best after market resin ejection seat I've ever used. The sidewall detail is also very nice. The photos below show the improvements I made to the sidewall detail. Although resin sidewall detail looks nice as a stand alone part if it is fairly thick and is stuck onto the inside of the fuselage it can make the fuselage even thicker and look like a detailed part that was stuck on as opposed to part of the fuselage. I decided to sand the part down and get it as thin as I could and in the end I was just left with the detail part of the sidewall and managed to sand away all the backing completely. A couple of smaller boxes and wires were lost but these were easily replaced or reattached to the side of the fuselage. I wished I had taken a pic before I sanded them down to show the difference. Revell 1:32 Hawker Hunter by Marks CVS, on Flickr Revell 1:32 Hawker Hunter by Marks CVS, on Flickr Here is the unpainted cockpit tub with the kit rudder pedals. Revell 1:32 Hawker Hunter by Marks CVS, on Flickr Here is the painted cockpit. First off I sprayed the Interior Alclad black primer. I then made a couple of mixes of HU33 Black and HU67 Grey to add some shading. I then painted all the switches in gloss black to make them stand out. The Instruments were also painted gloss black and had the dial detail dry brushed in white. Paint chipping was added using a silver pencil. The floor near the rudder pedals also had some zinc chromate primer painted round the silver but needs further black painting over and around it to blend it in. Revell 1:32 Hawker Hunter by Marks CVS, on Flickr Revell 1:32 Hawker Hunter by Marks CVS, on Flickr Revell 1:32 Hawker Hunter by Marks CVS, on Flickr Revell 1:32 Hawker Hunter by Marks CVS, on Flickr Revell 1:32 Hawker Hunter by Marks CVS, on Flickr The ejection seat was almost perfect from the box. The only detail required was the ejection handles and an arming pin made out of a plastic disk and a piece of wire. Revell 1:32 Hawker Hunter by Marks CVS, on Flickr The cockpit needs a few touch ups before I can close up the fuselage but overall I'm really pleased with how it turned out. Thanks for looking.

This was my choice for a quick build between finishing HMS Muskeeter and whatever I pick up at Telford, unfortunatly it rapidly turned into a nightmare............... no fault of the kit which is great (no Hunter expert this is the first i've ever built but it seemed like a very nice kit, if there's any real issues with it I didn't fix them!) Right from the off things went wrong Paint finish is a mess..... white turned yellow, masking was crooked, red overspray on grey areas, the red wingtips should extend further inboard (should have looked at pics instead of just relying on the xtradecal instructions) I then managed to place the two upperwing roundals assymetrically which meant positioning of the scratchbuilt pylon lumps on the upper surface were wrongly positioned..... and to round it all off I managed to pull the starboard serial number off with an errant piece of masking tape just before finishing up.... ETC Arrrhhhh really glad this ones behind me, may well build another in the future as the subject and kit look good (won't bother with the flightpath detail set as it proved to be a bit of a fiddly pain in the A***)