All Activity

I need some of these.

i agree, good start on the weathering. I am surprised how well cast the parts look with some paint on them. Especially the parts moulded in red look bad without.

Thank you all for your replies. It seems there are no straight forward answers without undertaking some very deep research, which I'm not able to do due to time constraints. That's why I bought the book! I should have stressed in my first post that I'm not criticising the book. I absolutely love it. One of the WIP comments caused me to start questioning things and I just want to do the best job I can for my friend. @Mark Postlethwaite I would dearly love to buy one of your new books as soon as they become available, if you wouldn't mind letting me know? Thanks again guys and have a good evening. Best regards Andy 🙂

time is here Gentlemen

That would be quite interesting, as the last time Sannites fought as an independent force must have been around 3rd century B.C. They probably had no aircraft to field against the Roman legions, which may explain why they were eventually subdued. "Aeronautica Sannita" would be, literally, "Sannite Aeronautical Company", a short-lived industrial activity located in Benevento, Italy. That is, "unit insignia": the 51st Stormo would have had the black cat with green mice. The Italian Co-belligerent Air Force used numerical codes including the Gruppo number (21 in this case) and the aircraft individual number, that were usually located on the "tail". For a Gruppo at the time, unit strength was probably that of a RAF squadron.

I've already got mine pre-ordered with Squadron and the local hobby shop, the 100th boxing. Should be fun!

I've been eager to see how the interior will look together, so take a look at the first photo. On the left is the cockpit and navigators position, then the bomb bay, and the radio station. I'm glad to see how it's coming together, and most of the work I've done since the last post has been to the bomb bay. The second picture is of the bomb bay door to which I added balsa wood pieces to. These are going to resemble the hinges of the door in its open state. They do need trimmed still, which I'll do later in the build. I already did some adjusting to the 3d bomb prints, and they've gotten pretty close. Secondly, I've sketched out on the bulkheads where I'm going to add the frames and general supports that was not on the model to begin with. The brown foam you can see in the picture underneath the bulkheads is where I'm going to add a piece of plastic to fill the gap between the bottom of the floor parts and the fuselage. However, the major issue currently is the attachment of the wings. It snaps in quite nicely, but leaves weird knobs on the inside of the bomb bay (In one of the photos, I circled in green what I'm talking about). I have a few ideas, but I don't want to compromise the structural integrity of the attachment of the wings. Anyways, I was also able to print some of the crew of this airplane. There is good news and bad with them though- I was able to get them sized perfectly on the first try, but they look at little rough. Well, really rough.😬 I foresee either a lot of filler, or a major change of my 3d printer settings. I think I'm going to decrease the head speed and maybe make the layers thinner. Either way, it may delay getting the fuselage together. Until next time, Joanna

Me too.....

try the blue-pill cocktail

That sort of nonsense seems to be the prevailing 'style' just about everywhere these days unfortunately.....

Available here as a pre-order for euro 55.86: https://www.aviationmegastore.com/en/modelling/kamov-ka-52-russian-attack-helicopter-zvezda-4830-202908.html

Eduard did a set for WW2 RAF uniforms in colour PE -1/48th scale, I have it somewhere in the stash but I do hold reservations on how good it would actually be in application. I think its long been discontinued?

Given that the Shinden was built largely in 1945, in considerable haste - and actually flew only just before the end of hostilities, it is quite likely that less attention was paid to painting and finish than would normally be the case for a prototype. Get it airborne ASAP, find out if it works. So having unpainted undersides is quite probable, Interior colours may also have been whatever was readily and rapidly avaialible, not necessarily to the precribed standard. John B

for a stiff drink

Nicely done and, like the others, looking close to what was pictured inside my head. I have a plan to read the whole lot of Discworld books again. They're sitting on the shelf ready and waiting.* * All except that last one about the steam trains. It was awful!

Nice preshades on the Mikasa. ⚓👍

love you long time

Uniform insignia, I found there are a few about from all era's, but always as part of an aircraft decal sheet.

Does she get discount for being a redhead? 😁

You pay ten Dollar

You will also need to reshape the ventral fairing and add a bit of filler to represent the 4-way fairing at the leading edge of the tailplane/.fin intersection. The doors for the undercarriage legs are too long and need a section removing from the top and gluing into the hole, then filling. The door will then need to be severely thinned and the kink at the bottom has a curve. I glued the main wheel doors in place then created a hole for the wheels, with a section removed where the outer door kink fitted. Fiddly but a great improvement. I have not yet approached the A Model kit re the same details.

EMA Plastic Weld may be your best bet, but no idea if you can get it in Canada.

Hello guys, some close up photos taken at NASM (after the Shinden was put on display) suggest that the canard undersides may be unpainted. Check these photos: https://447bg.org/ww2-planes/ww2-japan/j7w1-shinden/ For the cockpit: have you seen Robert Mikeshi's "report" on Shinden colours? You can find the information in the "Aviation of Japan" blog. It seems that the original interior colour would have been an olive green. Something like in that photo the OP posted. Cheers, Antti

That light gives it a moody effect. It looks fabulous. As for the bed. It's awful and I love it. Well used and showing it.

Worth a mint those kits