Jump to content

IDF Tiran 4. 1:35


Shar2

Recommended Posts

IDF Tiran 4

Takom 1:35

boxart.jpg

 

History

The meaning of Tiran [pronounced as Tiy-RAE-N] in Hebrew is beginner. Israel's chronic lack of AFV's on one hand and it's phenomenal victory in the 1967 Six Days War on the other, brought the IDF to adopt captured enemy vehicles for its use. The Arab armies lost hundreds of fighting vehicles - mostly Egyptian T-54 and T-55 MBT's which were abandoned by their crews.

 

In order to allow for greater standardization in its armour corps, the IDF initiated a conversion program. The captured tanks were re-engined and re-gunned (with the standard 105mm gun used in the Centurion and Patton MBT's). Chief was the several hundred captured T-54/T-55 tanks that were taken and modified into the Tiran 4 (T-54) and Tiran 5 (T-55), called Ti-67 (Tank Israeli-1967) in the west. The main difference between the two versions is the main gun armament. The Tiran 4 having a 100 mm main gun while the Tiran 5 having a 105 mm main gun.

 

  • The first version of the Tiran 4 is distinguished by a few minor additions such as two brackets, Jerry cans on the back of the turret and a new communication system. The rest seem to be original, even up to the ammunition.
  • The first standard Tiran 4 is one of several sub-versions of the Tiran vehicles. It was directly taken from the T-54 and received a set of different mud guards to the rear, a cal.30 Browning was fitted to the turret, and a box on the rear of the chassis which was also used on most of the Tiran versions.
  • The next version of the Tiran 4 was unusual, in that it retained its original 100mm gun, but fitted with a fume extractor. Many of these cannon are visible on other Tiran versions in the IDF.
  • The second version of the Tiran 4 was fitted with a few additional changes, such as antennas, hatch, and searchlights on the turret, along with spare track links, the biggest change being the fitting of the 105 mm M-68 main gun.

 

The first combat use of captured tanks by the IDF was in operation "Raviv" (8-9 September 1969) - an amphibious raid across the Suez channel. Three T-54 tanks and six BTR-50 APC's were used to wreak havoc behind the Egyptian lines. Tirans were used along Israel's borders - mostly at the Suez front. In the 1973 Yom Kippur war Tirans were used in combat in the southern front - against Egyptian T-54/55 (which caused a lot of confusion). During the 1973 war the IDF managed to capture the newest Soviet MBT of the time - the T-62. Plans for conversion into Tiran-6 were made, but the relatively small numbers captured, together with the massive numbers of M-60 MBT's supplied by the US brought them to a halt (several prototypes were made, however). During the early 1980's Tiran MBT's were withdrawn from active duty. Some were sold to foreign states (including, reportedly, to Iran during its war with Iraq), some were given to Israel's allies in Lebanon and some were converted into the Achzarit APC. Ironicaly, some of the Tirans supplied to the SLA (South Lebanon Army) militia fell into Hizballah hands after the Israeli withdrawal from Lebanon (June 2000). In a way, those tanks made a full circle.

 

The Model

We must be getting pretty close to having every single Russian/Soviet tank type being released in injection moulded plastic. At least this kit fills the gap between the JS tanks and the T-62s, and there weren’t too many versions of this vehicle when compared with the T-62 series onwards. Contained in a nicely illustrated box are fourteen sprues and two separate parts in grey styrene, a bag of individual track links in the same material, a smallish sheet of etched brass and a small decal sheet, oh!, and a length of wire. The moulding is superb, with no sign of flash or other imperfections, just a few of the usual moulding pips to clean up. The fact that the individual links are already off the sprue and ready to use is very helpful.

 

spruea.jpg

 

sprueb.jpg

 

hull.jpg

Construction begins with the lower glacis plate being attached to the front, the sprocket gear covers to the rear and the idler wheel assemblies to the front. Each idler wheel, which actually looks like a modified sprocket, each one is made up from seven parts. Each road wheel is made up from two wheels and two separate tyres, which will at least make it easier to paint, whilst the sprockets are just two parts, the inner and outer hubs. The slightly confusing bit is that there are three different styles of suspension arm per side, and up to three parts per arm, so take care when assembling and fitting each arm to ensure you are using the right parts for each particular side.

 

spruec.jpg

 

sprued.jpg

 

The upper hull decking is made up from front middle and rear sections, which, when joined together is fitted out with the drivers hatch, PE grilles, six piece headlight cluster, fastening strips, hooks and other sundry items. With the wheels and tracks fitted, the upper hull decking is attached to the lower hull, followed by the rear bulkhead and inner sprocket gearbox fairings. As stated above, each individual track link is all ready to be used, it’s just a shame they aren’t the click together type as seen in Takom’s Mk.IV and Mk.V Heavy Tanks. They are easy to fit and glue, but it might be an idea to make up lengths of them to match the point in the track and any associated sag required before joining them up around the sprockets and idlers, you will need around 92 links per side.

 

sprueh.jpg

 

spruej.jpg

 

spruel.jpg

 

Before the track guards are fitted several holes of various diameters need to be drilled out. The starboard guard is then fitted with the various storage boxes, angled support arms, spare fuel tanks, plus the front and rear mudguards. The pioneer tool rack and tools is fitted to the port track guard, along with the barrel cleaning kit tube, and more storage boxes. They are then fitted to the hull and the fuel tanks pipework attached to the appropriate tanks. The rear bulkhead is fitted with the mounting brackets for the two four piece auxiliary fuel drums and the unditching beam.

 

spruen.jpg

 

turret.jpg

 

spruex.jpg

 

The build then moves onto the turret, with the single piece upper section being fitted with the hatch rings, internal co-axial machine gun, various brackets, stowage eyes, sight doors, and hand rails before the gunners hatch, which is made up from no less than twelve parts, is attached, along with a sight. The much simpler, four part commanders hatch is glued into position, as is the mantlet cover, three piece 60mm mortar, two jerry cans, small two piece storage box, three piece large storage box, two, three piece aerial bases, and ten piece rear stowage basket. There are two types of main gun barrel, one with a fume extractor and one without, both made up from two halves split longitudinally, so care to minimise the seam will be required, or wait for an aftermarket company to release a metal barrel, the barrel is fitted in place and finished off with the separate muzzle end piece. The six piece 30cal Browning machine gun and eight piece 50cal machine gun are attached, the 50cal having alternate positons. The completed turret is then fitted to the hull at which point the build is ready for paint.

 

clear.jpg

 

etch.jpg

 

links.jpg

 

Decals

Whilst there are three schemes in the full colour paint chart the actual decal sheet is very small and is only required for two of the schemes, one of which only has registration numbers, the other has registration numbers, identification chevrons, and three white rings on the barrel. The schemes are for the following vehicles:-

 

decals.jpg

 

  • Tiran 4 of the South Lebanese Army, used during the Peace for Galilee operation 1982.
  • Tiran 4 of the South Lebanese Army, Negev Desert, early 80’s
  • Tiran 4 of the South Lebanese Army, Jezzine, 1985

 

Conclusion

Takom really are getting the most of their T-54 moulds, but this is still a very nice kit and looks like it will be a joy to build, much like their other kits. What with Trumpeter and Tamiya producing other versions of the Tiran series, you could end up with a full set.

 

Review sample courtesy of
logo.gifUK Distributors for logo.gif

 

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...