Jump to content

X-1 Mach Buster (8079) 1:48


Mike

Recommended Posts

X-1 Mach Buster (8079)

1:48 Eduard

 

boxtop.jpg

 

Bell built the X-1 as their attempt at breaking the elusive sound barrier as it was known then, although it was having problems with control at high mach numbers due to the lack of surface area on the elevators.  After agreeing to share data with the Miles company that were developing the superior Miles M.52, the US reneged on the deal after Miles had naively given their data over, after which the Bell engineers fitted an all moving elevator to their design, while the British government cancelled the Miles project.  This left the Americans free to break the sound barrier without any competition, reaching 1,000mph in 1948 with the well-known Chuck Yeager along for the ride.  The rocket propulsion system was later improved with added fuel tank capacity and achieved 1,450mph.

 

 

The Kit

This is a reboxing of the 1998 plastic with some additions and subtractions from the original Profipack boxing.  Inside the box are two sprues of dark grey styrene, a single clear part, a sheet of nickel plated and pre-painted Photo-Etch (PE), a bag of resin wheels, a small sheet of pre-cut masking material, decal sheet and the instruction booklet, which is printed on glossy paper in full colour at A5 size.

 

sprue1.jpg

 

sprue2.jpg

 

pe.jpg

 

This is one of Eduard's early kits and as such it has a "Classic Airframes shine" to the parts, and they aren't of the same detail and quality of their modern uberkits, and as such they should be considered as somewhere between short run and mainstream – "long run" maybe?  This is a simple kit however, and the lack of locating pins on the fuselage halves shouldn't worry any but the most cautious novice.  Construction begins in the cockpit, and with the choice of three different instrument panels, all of which are pre-painted, and a set of seatbelts that are also pre-painted, this part of the build shouldn't take long.  You will need to add a bit of nose weight behind the cockpit to make it sit on its nose wheel, but after that, you can close up the fuselage and add the wings.  A choice of either the original ineffective elevators or the later Miles inspired units are included, which depends on which decal option you choose. 

 

Before you put on the canopy, your choice of instrument panel is added along with the rudder pedals, which looks like it could be a bit fiddly, although you do also have the escape hatch to peer through during fitting of this assembly.  With that done, the faceted windscreen can be applied, and this is where those masks come in handy, saving you the tedium of cutting individual masks for each pane.  The escape hatch can be added closed if you wish, hiding away the little PE handles on the inside, or you can leave it off, but as it is not tethered, you'll have to come up with some way of keeping it with the model, such as a base, or gluing it to a wing.

 

clear.jpg

 

The landing gear on the original was simple, which is replicated by the kit parts, with the addition of some very nicely 3D mastered resin wheels to replace the soft detail of the original parts.  The gear bay doors however are a little agricultural, but this can be remedied by either applying a little modelling skill, or getting the PE Upgrade set that is now available under the code 48908.

 

 

Markings

The decal sheet is printed in-house, and the quality has improved since they began this practice.  The sheet is in good register, sharp, and with adequate colour density, having a closely-cropped glossy carrier film.  From the box you can build one of the following two airframes at different points in their careers:

 

  • 46-062 Muroc Dry Lake Base, 2nd half of 1947.
  • 46-602 Edwards AFB, 1950.
  • 46-063, Muroc Dry Lake Base, late 1946.
  • 46-063, Edwards AFB, October 1947.

 

Conclusion

It may be a little old-skool, but it is still a welcome re-release of this important little aircraft.  With a little care it should build up into a creditable replica of the real thing, ably demonstrated recently by our member Orangesherbert, or Simon as we prefer to call him.  You can see some more pictures here.

 

complete.jpg

 

Recommended.

bin.jpg

 

 

X-1 Overtrees (8079X)

If you don't need the decals, resin and PE parts for what you have planned, the Overtrees offer you the option of purchasing just the two grey sprues and the windscreen without the expense of the handsome box, instruction booklet etc.  It comes in a plain white box, as below:

 

8079x.jpg

 

bin.jpg

 

 

 

X-1 Photo-Etch (8079-LEPT)

If you change your mind about the PE, or you have an older boxing that you'd like to get the pre-painted instrument panels for, this little set is just ziplok bagged on a white card to keep it safe, as below:

 

8079-lept.jpg

 

bin.jpg

 

NOTE: Overtrees are available only from Eduard's website, so please bear this in mind when ordering.

 

Review sample courtesy of

logo.gif

  • Like 5
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...