Jump to content

GSI Acrysion Review


fayfaychu

Recommended Posts

I couldnt find any detailed review about this new type of paints despite it has been released for a while. So I decided to share some of my experiences with it with the pros and cons I have encountered so far. All paints were bought out of my pocket.

Firstly this is a paint that is completely new in terms of formula. I dont think it behaves like ordinary acrylics like Tamiya, Lifecolour, Vallejo, or even Mr Hobby's brand of water soluble acrylics. This paint is water soluble to a degree that you can clean your brushes with water when it is still wet. But it cannot be thinned with water. The drying time varies among colours, but normally it will dry in 5-15 seconds when applied by brush.

IMAG5278_zpsypjxxmui.jpg

IMAG5283_zps4abnrdhc.jpg

The consistency of the paint is like milk out of the bottle, which suits very much for airbrushing directly. However Mr Hobby has produced two types of thinners for the Acrysion line, and both has its own property that should be considered when applying. The drying time varies among colours, but normally it will dry in 5-15 seconds when applied by brush and this is where the thinners come into play. The solvent with blue label has a high retarding property that will prolong the drying time and can remove unwanted brush marks. Meanwhile the thinner in green label is meant for airbrushing and the labels says you need to shake it before use. Do shake it before use unless you want a really high gloss finish that dries in 24 hours! Dont ask me how i know it though...

After trying out the paints (i have bought dozens of them) the followings are noted:

1) I believed these paints are formulated for airbrushing. If thinned with the airbrush thinner they dont clog like the other arcylics do, and give a rather consistent appearance sort of like Mr Hobby lacquer line of paint. As the consistency of the paint is almost airbrush ready, you only need to add a few drops of thinner for each spraying session.

2) Coverage varies from colour to colour. Some of the colours is of a consistent liquid, while others, notably the white and grey ones, will have heavy pigment separation. For the gloss orange I showed here there are almost no pigments on the bottom but for the greys I always have to give the bottle a good stir before it becomes the colour it should be. The orange is also very transparent and required at least 3 coats before a solid colour is obtained. The coverage also varies from colour to colour and I think the orange is the most transparent I have experienced. I airbrushed on bare plastic, paint to thinner ratio around 70-30 (Can be unthinned as well), around 15 PSI. As you can see it produced a gloss finish that is hard to be done with acrylics. The humidity at the time of spraying is almost 98% but the finish wasnt really affect by it. I oven dried it at such high humidity to speed up the curing process.

IMAG5282_zpsbgw2o6um.jpg

IMAG5279_zpsyrrzcsqn.jpg

IMAG5294_zpsacmm5ll4.jpg

3) So why bother with this new line? Well first it claims to have 8x% less VOC than their lacquer paints, which makes spraying indoors more tolerable. An extract fan is definitely needed but after say 1 min of spraying there is no smell what so ever left. Secondly it produces a coating that is so hard and durable that it almost compares to lacquer paints. Masking can be done almost immediately after it has cured and I have not experienced any lifting at all.

IMAG5280_zpsqvitdl9v.jpg

4) Some thinners (Lacquer and enamel thinners) can still dissolve it, but not with alcohol, Mr Hobby's own weathering thinner and water. After airbrushing I often find paints dried inside the airbrush cup and deep cleaning should be done first with water then their own tool cleaner.

So the cons of the product? First the properties of it required practices. I made mistakes by thinning it too much and spraying at a low pressure, and the surface tension just got me. Some colour may appear to have a rather thick consistency but a few drops of thinner is really all it needs. These two bottles lasted me for couple months and is still more than half full.

The drying time can varies and it is best to practice on scrape plastics before the formal application. Priming is not a must but will certainly help. The choice of colour is rather limited at this time but Mr Hobby seems to be expending the range slowly so we will see.

The bottom line? I think I will use this line of paints for painting the base colours of a model, where masking is often required for the succeeding layers. It has a higher learning curve than most arcylics, and is not as convenient that the likes of Vallejos. But is durable and considerable less toxic than lacquer paints. Hopefully Mr Hobby can come up with a wider selection to suit more purposes.

Sorry for the long post.

Edited by fayfaychu
  • Like 2
  • Thanks 1
Link to comment
Share on other sites

Thank you very much for the test and review of the Acrysion acrylics. I bought some of these paints last year through EBay, but I've been unable to find the two thinner types - for brush and airbrush, respectively - readily for sale anywhere. Where did you purchase yours??

I'm eager to put these new paints to use. From what little experimentation I've done with them, they have almost no discernable odor. On GSI Creos' website it appears that the coming months will see them roll out additional colors in the Acrysion range. It looks like they're trying to mirror the availability of colors in their popular Mr. Hobby Color and Mr. Color ranges.

Edited by GPBooth
Link to comment
Share on other sites

Thanks for this! Never heard of these paints before but my paint of choice was Mr Color, until I moved and lost the garage as a spray room! I like the idea of odourless paints that spray like Mr Color!! I'm off to trawl eBay....

Link to comment
Share on other sites

  • 3 weeks later...

Gloss paint has never really worked for me regardless of the brand. For this particular model I mixed up gloss black with Gold with portion 10:3 (black to gold) as per instruction. The paint layer was thin, but I needed to bake the painted parts in order to obtain the shine for the monocoque. Other parts worked fine.

IMAG5377_zpsvhx17s3j.jpg

IMAG5376_zpsiokkqrea.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...