Jump to content

+++ FINISHED 06-09-2018! +++ Boulton Paul Defiant Mk I (Airfix 1/72 Dogfight Doubles)


Recommended Posts

This thread started life as one of my entries to the Battle of Britain GB back in 2015. As usual, I didn't finish in time and it remained in the shelf of doom till now.

 

I'll try to finish it now...

 

-------------------------------------------

 

 

Dear All,

 

this is my first entry in the BoB GB: Airfix's Defiant from their 1/72 Dogfight Doubles boxing, which also includes the Dornier Do 17z.

 

These two aircraft met over Britain in August 1940. The Defiant managed to shoot down the Dornier but was, in turn, itself shot down next by an escorting German fighter.

 

The aircraft I'll be building was based in Martlesham Heath, where BT Labs were later built. This is quite meaningful, personally, because I did my MSc. Project there in 1993-4 (on self-pulsating lasers for fibre optic communications systems, by the way).

 

Here is the box, the Defiant sprues, the PE and masks I'll be using for the build:

y4mBCToyEveH-k79ggDI6aH-kehXve23VgytHkkk

IMAG2300

 

I won't be starting this any time soon, because I still have to finish my three British Phantoms for the Phantom GB. I'll start planning the building of the Defiant (and Dornier) this coming weekend, however.

 

This is a very ambitious build for me, since I still haven't used any PE in my previous builds. So, with three kits to build (the Defiant and the Dornier of this box - WIP here, plus a Tamiya Bf 109 E4 - WIP here), limited time and a lot of PE without previous experience of it, what can go wrong? :)

 

Cheers

 

Jaime

  • Like 7
Link to comment
Share on other sites

Sounds good Jaime. I'm sure you will make a good job of all three. Joe :)

  • Like 1
Link to comment
Share on other sites

I think this sounds like another fine project to follow. Looking forward to seeing what you do with them (once you get around to starting!)

  • Like 1
Link to comment
Share on other sites

Nice choice. Are you building them "in flight" using the stand??

Thanks Greg. No, I always build my aircraft "wheels down" and with as much exposed detail as possible (opened canopies, dropped flaps if available, etc). Mind you, the box comes with a stand for displaying both aircraft "in flight".

Sounds good Jaime. I'm sure you will make a good job of all three. Joe :)

Thanks for the kind words, Joe. Coming from you, they mean a lot!

I think this sounds like another fine project to follow. Looking forward to seeing what you do with them (once you get around to starting!)

Thanks for your interest Stix. I hope I won't disappoint.

Cheers

Jaime

  • Like 3
Link to comment
Share on other sites

Thanks Greg. No, I always build my aircraft "wheels down" and with as much exposed detail as possible (opened canopies, dropped flaps if available, etc). Mind you, the box comes with a stand for displaying both aircraft "in flight".

Thanks for the kind words, Joe. Coming from you, they mean a lot!

Thank you Jaime, that's very kind of you. :)

Thanks for your interest Stix. I hope I won't disappoint.

Cheers

Jaime

  • Like 1
Link to comment
Share on other sites

Hello again,

 

I probably won't be able to start building in the next two weeks, but I'm using some time away from the bench to start planning this build.

 

Last night I managed to go through the instructions and made a listing of the paints needed. I won't be using the pilot figures, so here are just the colours needed for the aircraft. I converted the Humbrol call outs to the Gunze paint codes I'll be using:

 

Hu 24 (trainer Yellow) = H34 Cream Yellow (propeller tips)

Hu 29 (Dark Earth) = H72 Dark Earth (camouflage)

Hu 30 (Dark Green) = H73 Dark Green (camouflage)

Hu 33 (Flat Black) = H12 / XF-1 Flat Black (for most flat black parts)

Hu 33 (Flat Black) = H77 Tire Black (just for tires)

Hu 34 (Flat White) = H11 / XF-2 Flat White (Propeller spinner)
Hu 53 (Gunmetal) = H28 Metal Black (for guns)

Hu 53 (Gunmetal) = H76 Burnt Iron (wheel wells, wheel hubs, exhausts) - is this correct?

Hu 78 (Cockpit Green) = H312 Green (cockpit interiors)

Hu 90 (Beige Green / equiv. Sky) = H74 Sky - Duck Egg Green (undersides)

 

As said above, I won't be using the pilot figures but noticed an odd colour indication: Hu 90 (Beige Green, equiv. Sky) for the faces?

 

Also, were the wheel wells and wheel hubs really gunmetal coloured?

 

Thanks for looking

 

Jaime

  • Like 1
Link to comment
Share on other sites

Hi Jaime,

I'd go with interior green or sky for the wheelbays and aluminium or black for the undercarriage legs - aluminium for the wheel hubs. Feel free to ask around though, I'm not an expert :)

Cheers,

Stew

  • Like 2
Link to comment
Share on other sites

I'd go with interior green or sky for the wheelbays and aluminium or black for the undercarriage legs - aluminium for the wheel hubs.

Thanks Stew. Curiously enough, the instructions direct us to paint the undercarriage legs black and the inner surfaces of the wheel well doors sky (!)

  • Like 1
Link to comment
Share on other sites

Hi Jaime,

Well, it is feasible, the undercarriage legs may have been lacquered black and the wheelbays and doors may have been sprayed sky when the underside was repainted in that colour in June 1940 - equally they might not - the problem is the Defiant's defining feature is that big turret on the back so most pictures taken include that, which means you generally can't see the undercarriage or the wheelbays :shrug:

Cheers,

Stew

  • Like 1
Link to comment
Share on other sites

  • 3 weeks later...

Hi again,

 

I'm starting the work on my BoB GB entries, at last. I'm beginning with the transparent parts, just to mask them and put them to the side right from the start.

 

I'll build the Defiant with an open canopy.

 

As in the Dornier, I used my recently acquired RB-productions micro saws to cut the parts off the sprue. Here they are, just after cutting:

y4mxXZ16Q3zklm346sJctO4CV9GmQmIaH2qUb9D-

IMAG2524

 

I made the cuts well away from the parts, in order to avoid any damage from mechanical stress. I can say that the micro saw used works really well.

 

The excess plastic was removed with x-acto blades and sanding sticks (see my technique in detail here). Here's the final result:

y4mZGUGt1jX4Aha-01yZDtZJ3G-aQdn4tlmJF0y8

IMAG2526
 

I washed the parts with water and dishwasher liquid, to remove all dust, and then gave them an Aqua Gloss bath. Here they are, ready for the bath:

y4mbEcYfiWj-2h5dhWsS4ayhPBz8gKK2ThpwnRN9

IMAG2529

 

And here they are, drying:

y4mUqtD6Ohj05UOWdbYj0YmRqT_fzEjLMe6TdKjw

IMAG2530

 

When dry, I had to remove a few specs of dust that attached themselves to the wet varnish and then gave the parts another Aqua Gloss bath.

 

They are fully dry now and look really good: brilliant and transparent.

 

Next step: masking. For this I have Eduard's mask. It'll be my first use of pre-cut masks and I hope it's worth the price.

 

Thanks for looking.

 

Jaime

  • Like 3
Link to comment
Share on other sites

You've been very busy Jaime. Another good set of transparencies. Joe :)

  • Like 1
Link to comment
Share on other sites

  • 1 month later...

Hi again,

 

Continuing the work on my GB entries, yesterday was the turn of the Defiant.

I took the main fuselage, wings and cockpit parts off the sprues and spent some time cleaning them of moulding marks and subtle flash. Not as bad as the Dornier, though, but the plastic is also on the soft side. Here are the parts after cleaning:

y4mAcN0ipAZRgsX20GbWa5KKtmGt8EVOidZY_kJ8

IMAG2620

 

Fortunately, the ejector marks on the inner walls won't be visible after assembly of the cockpit parts and closing the fuselage.

 

I did a dry-fit test, to check for potential fit problems:

y4mP87lN0Wrf3WIwT4fQFTpm-qzcdf_jig2_FU8U

IMAG2621

 

y4m4WxQ8fxLFo157rTMl-4lBmSnk7izgdYaN8c1N

IMAG2622

 

The fit is good, just with a slight misalignment of some panel lines on the fuselage. The main problem may be with the wing root of the port wing.

The wing root of the starboard wing seems to be perfectly aligned with the fuselage:

y4mR8f7l4fFJW9o62dYS5POTPG9wXOS-5E384rYA

IMAG2623

 

However, on the port side the fuselage is just a tad wider than the spacing between to top wing parts:

y4m3fmNA-QKeKl5sRiByQgl9ihLLLYaIz2iE_BE3

IMAG2626

 

This can be solved by bending the port wing slightly downwards, resulting in perfectly horizontal central wing sections, with no dihedral. I've check some documentation (https://boxartden.com/reference/gallery/index.php/Modeling-References/Camoflage-Markings/08-Boulton-Paul-Defiant/Boulton-Paul-Defiant-8-04-960) and its seems this is correct (at least the top surfaces of the central wing sections seem to be perfectly horizontal). Please note that I didn't install the piece with the wheel wells that goes in the centre of the lower wing part and which, by itself, may make this apparent problem non-existent.

 

So far, so good, then :)

 

The next step is to start building the cockpit, with its associated PE parts.

 

Thanks for looking

 

Jaime

  • Like 5
Link to comment
Share on other sites

Hi again,

 

I've done some work on the PE parts for the Defiant.

 

Some of the PE parts are pre-painted but the interior green they used is not similar to the one I'll be using. So I will repaint these PE parts as much as possible. Some of them have two colours, as can be seen here:

y4mUBEJisU_D03ZIkkpQKoSrV6jT-JUvj7JZ-yuf

IMAG2627

 

So, I started by masking the black areas:

y4mVV_C-HB_CndWE0s36uDBmb5143AuFpD0haS51

IMAG2628

 

Then, I applied the only two PE parts that go on the inner cockpit walls and can be painted together with these walls:

y4mHE1-gmgZeo-gf65auA02hCyzkDoSUolWSTaVR

IMAG2631

 

y4mwV3xITGXwWOkDPabWjGkO7n8XHQ2DDO5HPJVb

IMAG2644

 

Following this, I took care of the plastic parts that also go on the inner walls. These will be painted black and after painting some PE bits have to be applied.

 

I had to cut out the throttle quadrant from this one (before / after, side by side):

y4mc0wZ6iCk1NIovraK0qp8-iyJhVzc5jswxoQPC

IMAG2629

 

y4m4l0GP-KJfRuYcyxQOw7q4tQk5FZiGZ48Zh6jx

IMAG2630

 

On this one, I had to remove some raised detail that'll be replaced by PE (before / after, side by side):

y4mYPA0VHGocRVSkAYjICGwTJkqVVWCPjGVuQ7pL

IMAG2632

 

y4mIeBx-EVDE53xr_NpdhBtecOWxmBQPO7iqfHsJ

IMAG2633

 

The next step was to deal with the seat, that is completely replaced by a PE part that must be folded and bent. Here's the part's top and bottom sides:

y4m9ivai7-1ERwN7fuQ3oX31WQfkh8vAYdyGzlWW

IMAG2634

 

y4mLFRn82FvRkw0QbEHiPgqx2-3dCIXqPwG_hNMm

IMAG2635

 

Before folding, I had to create the depression on the seat's centre. This was done with the tip of a brush's handle:

y4m9lL_WPSs5wJNVI3w4hqQm_pclcrfJhBjDmo6U

IMAG2636

 

Then, it was folded. Here it is, side by side with the kit's original seat for comparison:

y4mtu7iGDmfBAzyjWCAi_esQuFhN41hQmxvuxuuL

IMAG2637

 

The seat is mounted on the rear bulkhead by a supporting structure, like shown in the PE instructions:

y4mUPMpDia0Mu9Xiwun3HRofinDYOxiQGqiWzntV

IMAG2642

 

The part was bent:

y4ml2ewgrgVOSXNlemvA9xYfBNbwN3IZhFGDcOBu

IMAG2640

 

And glued to the back of the seat:

y4mPEjQAqEXdSdsSf9tMciiOKSrY2uystNqWpha-

IMAG2641

 

The rear bulkhead must have a hole made for the seatbelt to pass through:

y4m2giTJTXbrwkIni72RPxMTBWR7s9sYHA0sMah3

IMAG2638

 

This was opened with a pin-vice and x-acto blade and the PE part nº 3 was applied:

y4mNhEqd7NV9oA-uhPrFFPBXFJyWhVhrAQzGxfpu

IMAG2639

 

y4mbF-ASa-n4TacOzCrrpiG4JBGIO2nifTkU9U2v

IMAG2645

 

Here we can see most of the cockpit parts, both plastic and PE, as well as the original kit's seat:

y4mAr0OytXAVq_zsyuxz9wwIMZRpGH5ChNheXyGB

IMAG2643

 

There are a few additional PE and plastic bits to take care of before assembling the cockpit base, seat and bulkhead. Then priming and painting with the interior green will follow.

 

Thanks for looking.

 

Jaime

  • Like 7
Link to comment
Share on other sites

Hi again,

 

I spent the weekend away, but I managed to do some work on the Defiant last night.

 

Continuing with the cockpit work, I applied, on the seat's front, a PE part where the control column will be inserted:

y4mZ-lBDQGhL0V4is5cCPigX0cwgA4zrN8tWxp9o

IMAG2647

 

Then, I assembled the cockpit's base parts. The bulkhead supporting the seat is not yet glued to the base, because I think it will be easier to paint these separately. The pedals also have PE applied, representing the pedals' harnesses. The kit's seat is shown for comparison:

y4ma3CEO6KZ5d-ln3c_O5Fm1aQtdPTvCkz00vhS5

IMAG2648

 

Having done this, I moved to the instrument panel. This will be made up of PE parts instead of the decal provided with the kit. The PE panel is a multi-layer affair, consisting of several self-adhesive parts.

 

We start with the plastic part that comes with the kit:

y4mvRQVS4DKu5IoWrTdUAeZX71eTaOqDzRDJqZR3

IMAG2649

 

The lower stub, representing the compass, is cut off and the first PE layer is applied:

y4mFNAwKL0fBDGthT2FBq6V5Ui3QPBLTLZQv4Oxp

IMAG2650

 

Then, the second PE layer is applied. This one comes with the compass, which must be bent and set in the horizontal position:

y4m_0rXV93e2T8Al2iW-6lOxwLZ3_XQh6wKD1NW_

IMAG2651

 

The final PE layers are applied. resulting in this:

y4me5mwRtth5pxRgGR_xMdI4U4Z4zeeSyxQn8Ov7

IMAG2652

 

To finish with, I removed the small area of plastic that can be seen just above the compass, on the lower edge of the IP. I should have done this right after the application of the first PE layer:

y4mrVvQFtwV3SQabpIGcIlZRgvQMFuhv_iISxOkq

IMAG2653

 

Here are all the parts that are ready for painting:

y4mweCqyvykpMwIwdqgUqq1GPfkXYaYl1tNaj9F4

IMAG2654

 

I still have to mask the transparent parts before painting.

 

Thanks for looking

 

Jaime

  • Like 5
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...