Jump to content

1:32 Tamiya Spitfire IX, 81 Sqn, Tunisia, Summer 1943


Kallisti

Recommended Posts

Inspired by robvulcan and PC2012's builds it is now my turn to have a bash at a large scale detailed Spitfire. This is another in my series of builds "Aircraft my Father Fixed".

Up to now I've built mostly the aircraft my Father worked on while in Burma in the latter half of WWII while attached to 5 Squadron. before that he was with 81 Squadron from their entry into Operation Torch at Gibraltar Oct '42 up until Sicily had been pacified in Oct-Nov1943 whereupon he was transferred to Cairo en-route to India and 5 Squadron. Funnily enough, 81 Squadron followed his his wake a couple of weeks later and ended up based 5 miles down the road in India, re-equipping with Spitfire VIII, hence why I have a Christmas dinner menu from 81 Sqn in 1943:

DSCF4781.JPG

DSCF4782.JPG

Anyway, back to Tunisia in the spring/summer of 1943. Up to that point, the squadron had been equipped with Spitfire Vb Trop and Vc Trop (hence my earlier abortive attempt to convert the Hobbyboss Vb Trop to a Vc Trop), however these were beginnign to be outmatched by the German aircraft. The Tropical filters used on the V series had an unfortunate side-effect of reducing overall performance of the engine. So in May '43 81 Sqn started receiving Spitfire IXs. At this point they were based in Tunisia at Souk-el-Khemis airfield and subsequently moved to other airfields in the general vicinity.

From reading Alan Peart's book "From North Africa to the Arakan" you get to see that conditions on these airfields were basic to say the least. So I want to try to capture a snapshot of the activity of the groundcrew in these conditions in my diorama.

So to begin with, the model - you've all seen plenty of sprue shots so I won't bother here, but at least here is the box:

DSC_0382.JPG

For the base I'm using a 300x300 wooden base supplied by one of my IPMS Farnborough colleagues from his website: http://www.ema-heritage.com/displaybases.html

DSC_0384.JPG

That should give enough space for the aircraft and some activity around it. Speaking of which, the donor kits for figures, materials etc include this lot:

DSC_0383.JPG

Yes I know there is 1:35 scale figures in there but my Dad was only 5' 5" tall, so they'll be okay :) On th eleft you can see some of the ValueGear stuff that I used in my Hurricane diorama earlier in the year. This stuff is superb, huge variety and excellent casting and detail. I picked up a set of crates as well which you can see in the glass ashtray in the top left. Above that is the IconAir accumulator trolley I built originally for the Hobbyboss build. I've added a small engine on the top of it to represent the generator that was fitted to many of them. This was sourced from the US Maintenance Yard kit from the compressor you can see at the bottom right of the box top picture.

For the Spitfire I've got a collection of Decals for the inside and outside that will allow me to represent EN204 FL-L:

DSC_0401.JPG

(from the Osprey book "Spitfire Aces of North Africa and Italy)

Note how the original "E" lettering has been badly overpainted to turn it into a "L" :)

Here are the decals I'll use:

DSC_0385.JPG

There is a huge amount of aftermarket stuff for this kit and here is a selection of what I may or may not be using:

DSC_0386.JPG

There are wheels, seat, large cannon wing covers, cockpit door with seperate crowbar (not to be painted red!!), Cockpit upgrade set, cockpit stbd sidewall, "cloth" seatbelts PE Toolbox by Aber (just like the one I have in the Hurricane dio) and finally the PE set for the Hobbyboss Vb, but which contains some very useful bits for this build, eg the PE radio hatch door which will be used elsewhere on this build!

I actually started this build a couple of weeks ago but haven't got very far because in the weather we've been having the man-cave shed is to flipping cold!! So I've come up with a cunning plan... Part of the delay was waiting for all the parts to arrive and also to do the research for the various things I want to do. Here is a sample of some of the reference material I've collected:

DSC_0396.JPG

This of course doesn't show the e-book PDF of Monforton's book or the other reference photos, sites etc that I've used and will be using. I've printed some of the engine photos and stuck them up:

DSC_0397.JPG

which gives away my cunning plan to get around the cold weather situation... move a lot of the modelling stuff into a temporary table in the lounge! All the airbrushing will still have to be done in the shed, but at least I can build and brush paint in comfort!

I began on the figures as I was waiting. I picke dout two from the 8th army set and one form the Tank riders set:

DSC_0387.JPG

The Tank rider figure in grey had to have the top of his head rebuilt as I won't be putting a steel helmet on him, instead he'll get an RAF side cap at a suitably rakish angle!

I began work on the engine and my aim is to add as much detail as I can bear to. The inspiration for that is the amazing Hornet build being undertaken by airscale in another thread here: http://www.britmodeller.com/forums/index.php?/topic/234950214-hph-de-havilland-hornet-sea-hornet-f-mk22-tt202/ Truly magnificent stuff and if I can get anything approaching this, I'll be very happy!

Progress so far:

DSC_0388.JPG

Its all a bit bland and OOB so far - well apart from the replacement resin rocker covers with the Rolls Royce logo on them. This will change as time progresses I hope.

Now since I've got an accumulator trolley in The diorama, there should be somewhere for it to plug into:

DSC_0390.JPG

Voila! So of course there is also the question of the starboard rear panel I've been pestering people about on another thread... this one:

DSC_0389.JPG

As you can see I've successfully cut it out without causing damage to the surrounds and next to it is the PE Radio access panel from the VB PE set which is near enough the same size (its about 1.75 inches too tall, but that won't be noticeable when its hanging open. Here is the inside of it:

DSC_0393.JPG

which has superb fine detail. One of the things that my researches show for this access hatch is that the inner frame is very visible, with all its lightening holes present. So I'm going to have to scratch build that so that means removing the existing rib detail in the kit:

DSC_0394.JPG

So thats where I stand so far - bloody hell its taken an hour to write this post! I'd better get on with the rest of the day...

Edited by Kallisti
  • Like 5
Link to comment
Share on other sites

Oh yes this is gonna be fun. So cool I inspired you thats a first for me on here..... Cool.

I will watch with alot of interest my advise is don't set yourself a strict deadline Just take your time and a perverse amount of pleasure from every stage of the build and it will be awsome.

I am curious to see what you do with all that dio gear.. I wonder how long she will take you.

Happy Christmas Kallisti

Cheers Rob :popcorn:

  • Like 1
Link to comment
Share on other sites

Thanks for all the interest, hope you all had a great Christmas!

I got some work done on Xmas Eve, working on the rear fuselage panel considering the information I've been able to gather thanks to help from people on my thread in the WWII forum. So here is the open panel:

DSC_0412.JPG

Here is what you would see inside - I've added horizontal ribs to the far side of the inner fuselage plus 4 sets of control wires and supports for them:

DSC_0411.JPG

I may need to strip the paint off the wires as it looks like the spray primer had gone all blobby without me noticing before I sprayed XF 16 over it. Problem I face currently is the shed is too damn cold to spend any length of time in and I think the cold is affecting the paint drying so it went a bit blobby :(

The inside of the starboard fuselage has had some surgery to dig out plastic from the beack side of the moulded ribs either side of the hatch:

DSC_0410.JPG

This allowed me to drill out the lightening holes in the ribs:

DSC_0409.JPG

DSC_0408.JPG

which looks pretty authentic to me! I've also scratch built the tray for the battery and the battery itself plus its cover to prevent shorts. This needs a pair of tie-downs either side that connect to the lower tray, but they'll be added later as the tray and battery will have to be inserted into the fuselage through the hatch panel once the fuselage is closed up. Not sure of the colour of the cover as I've only ever seen diagrams of it, not a picture. I suspect it might have been wooden, but still need more info about that detail...

  • Like 2
Link to comment
Share on other sites

Begun work on the cockpit now, but sadly I appear to have misplaced the PE that came with the kit. I know I had it last week as I cut off the metal tabs that are used by the magnets in the engine covers, but now I can't find it anywhere so can't fold up the compass bracket :( going to have to turn the house upside down I think... I can't imagine that I would have accidentally thrown it away...

Link to comment
Share on other sites

I solved the problem for now by getting the PE from my Spitfire VIII I had in the stash and then writing to the UK Tamiya distributor to get a replacement one for that kit. I bought the Spitfire VIII a year ago or more when I first thought my Dad had been with 81 Sqn in Burma, but it ended up he was with 5 Sqn in Burma. I still plan on building it eventually as an 81 Sqn aircraft later.

Another update will be along shortly...

  • Like 1
Link to comment
Share on other sites

Had a fun couple of days watching old movies on TV and modelling - its nice having the modelling workbench in the lounge at Christmas. Rocky Horror Pitcure show was on Channel 5 late last night so there were of course moments where the modelling had to be put aside for some Time Warp dancing, ahem! (Its just a jump to the left...)

So attention has moved to the cockpit which out of the box from this kit looks superb anyway, but with a few additions can be pretty impressive. To that end, I picked up the Barracuda Starboard cockpit wall accessory as I've never seen this before. Wow its a work of art! Scaping the area from the inside of the fuselage was a PITA, but the resin insert looks great - check it out yourself...

DSC_0415.JPG

I've added a few extra wires from lead wire and mild steel wire. Then the instrument panel has been enhanced with some cockpit placard decals that came with the Baraccuda cockpit enhancement set. This is the second time I've used this as I used it originally in my aborted Hobbyboss Vb -> Vc conversion earier in the year.

DSC_0416.JPG

The joystick is from this set and has wires added to the column. next, the seat is the Barracuda replacement with the padded back. here I've tried to show some wear on the leather backing as this is a hard-working aircraft. You can also see the cloth seatbelts from HGW which took virtually the whole of this afternoon to put together this some very tiny bugles, eyelets and fastenings, but looks superb.

DSC_0417.JPG

Here you can see some sand wash added to weather them down...

DSC_0418.JPG

Then attention turned to the port wall which uses mostly kit parts, apart from a resin replacement throttle assembly. Here I added lots of extra wires and details, most of which will not be visible when the fuselage is closed up lol. Of course I then forgot to take a photo of it before attaching it to the rest of the cockpit - sigh

So here are the best photos I can get of the port cockpit wall

DSC_0422.JPG

DSC_0426.JPG

Here you can see under the seat the black/yellow twisted wire I made up from painted lead wire. SDly it won't be seen from above :(

and here things have been dirtied up a bit more

DSC_0428.JPG

One final photo which shows the compass, stick and instrument panel.

DSC_0429.JPG

Tomorrow should see the fuselage closed up which will mean I can insert the battery tray and battery itself!

Edited by Kallisti
  • Like 1
Link to comment
Share on other sites

Kallisti this is looking mouth wateringly good. Its modelling porn as far as I am concerned. I am glad you sourced your parts. :)

I have made a minor balls up on my tamiya Vb and got two parts on the wrong way around in the pit. But looking at this I shouldnt worry as this makes my work look like child scrawl.

Loving the build currently supping on a pint of Ale so a Big Cheers to you Rob :drink:

Link to comment
Share on other sites

Hi Kallisti, I have now read and fully digested and my gosh its looking most impressive already - but I should have expected nothing less. I know its a way off but I am looking forward to that base diorama coming together, I bet it will be another cracker.

Regards,

Nigel

Link to comment
Share on other sites

Fuselage was closed up yesterday which meant adding the battery and tray...

DSC_0431.JPG

Its dofficult to know if this is accurate as I've never seen a photo with the hatch open and the battery in place. All the photos I've seen so far have been of an empty compartment. Then again I suppose if I've never been able to find a photo, will anyone else viewing the model know better? :)

You can also see the hole I've already drilled for the IFF wires that will be added later. I've made sure these were drilled at a oblique angle to the line of the wire right.

Here is the cockpit again now its closed up - I'm very pleased with this cockpit, I'm just hoping that the engine detailing will turn out as good!

DSC_0433.JPG

I've been working on the wings but there isn't much special here, they are pretty much out of the box. However, I did end up using the kit canon covers on the top wing as the Barracuda resin replacement were too small and to be brutally honest I didn't fee like trying to sort out the gap!

Today the wings and fuselage will be joined...

  • Like 1
Link to comment
Share on other sites

But did a Mk.IX in the Summer of 1943 still have these IFF wires?

There is an ongoing discussion about this here under the heading:

All The (stupid) spitfire questions here.

NPL

Edited by NPL
Link to comment
Share on other sites

Well I never, I found this photo of the aircraft I'm building in May 1943:

81sqdn-spitfire9-fll-tunisia.jpg

on this page: http://www.spitfireperformance.com/spit9v109g.html

which although it not the best quality, doesn't seem to show any IFF wires, so I shall dispense with that plan!

Thanks for pointing that out, saved me making a "schoolboy error" :)

Edited by Kallisti
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...