Search the Community

I have seen TSR.2's at Duxford and RAF Cosford so I thought I would have a go at building one so here it is. The box has a picture of a TSR.2MS from a kids TV series but the kit has an option for the TSR.2 at both museums.I have bought Eduards photo etch set as well to add a bit more detail.As I usually do I am going to have this in a flying display with the stand made from brass tubing mounted on an oak base. So the first thing I am going to do is to workout how I am going to do it. After a few hours of studying the instructions and examining the fuselage parts I decided to mount a long steel bolt through the centre of the part that made up the rear wheel well and bomb bay. So I hand drilled a hole to take the bolt and I attached it to the part using epoxy. The epoxy is fast drying but I left it over night to cure.As you can see from the photo's I have added the epoxy at both sides of the hole for a bit more add strength. The I glued the wheel well to one fuselage half along with the front wheel well. Then I added some photo etch detail before I attached the cockpit tub. The reason for doing all this is because the fuselage halves are a bit bent and twisted so I wanted to make sure that the part holding the mount has a really strong bond.To help the fuselage halves line up better I also attached plastic tabs made from thick plastic sheet.After test fitting and test fitting and test fitting again I still have not attached the fuselage halves as there were other things to do before I could attach them together.Because of the way and location of the mounting bolt I glued the doors of the bomb bay in the closed position. Then marked and drilled the hole through the bomb bay doors. Again to add more strength I glued a piece of thick plastic sheet to the back of the doors. The width of the plastic was cut to allow the plastic to fit inside the bomb bay housing again add strength.Then again I did more test fitting.This time I tried test fitting the wings to check the symmetry with the fuselage.My attention then moved to the air in-takes. These had a few gaps that required filling and then sanding to try and get the inside of the in-takes as smooth as I could.I then moved to the jet exhausts assembly which went together without any problems.So with all this done I sprayed the inside of the cockpit and then I finally got around to gluing the fuselage halves together with the help of a few clamps.Once the glue was dry I attached the air in-takes to the fuselage. I also glued the bomb bay door assembly to the base of the fuselage lining up the steel bolt with the hole in the bomb bay doors. As this is a flying display I had to glue the undercarriage doors in the closed position. The doors are not a good fit so I used right angled plastic rod to help support the doors.Then in was just a case of filling the sanding then filling and sanding until it looked right.The cockpit tub and the fuselage had a few gaps that required filling thats why I haven't added the seats, pilots or instrument panels.I decided to use a pin for the pitot tube instead of the plastic kit part. I drilled a hole in the end of the nose cone then I dropped a few drops of CA glue into the cone then I pushed in the pin. The pin was one of those with a bead on the end which helped it attach a touch better to the cone giving the pin head more surface area for the glue. I then trimmed the end of the pin with a pair of wire cutters taking the length from the kit part. Out came the filler again and I sanded the nose cone smooth.The wings were then attached which was an easy job and the fit wasn't too bad. The fit for the tail plane was a bit too loose so I added a copper pin to the rudder and elevators which was just a case of drilling a hole in the base of the rudder or elevator. Then attaching a small piece of copper wire with CA glue then cutting to size. Then I gently pushed the rudder or elevator in position on the fuselage so the newly installed copper makes a mark. Then I just drill a hole at the mark on the fuselage for the copper pin. Its then just a case of attaching the rudder, etc using normal plastic glue.After I had attached the rudder I glued in position the jet exhaust assembly then I did a bit more filling.Now its is starting to look the part.