Jump to content

Pilot Officer Prune

Members
  • Posts

    64
  • Joined

  • Last visited

Everything posted by Pilot Officer Prune

  1. Interest registered for 1/48 please, and possibly 1/72 as well!
  2. Supermarine Spitfire FR Mk.XVIII, TZ233, 208 Squadron., RAF, Fayid, Egypt, 1948/49 The aeroplane is painted in the short-lived ‘Post-War Desert Scheme’ of Dark Earth and Light Slate Grey over Medium Sea Grey. Anecdotally, the scheme was rushed into service to reduce confusion and aid identification during the Israeli War of Independence, when the Israelis, the Egyptians and the British were all flying Spitfires! 1/48 scale Airfix Spitfire FR.XIV kit, modified to Mk.XVIII by leaving the wingtips on, using the large rudder, modifying the wing panel lines to remove all traces of the outer gun bays, and cutting the under-fuselage camera ports. I also added an Ultracast seat, and a Gyroscopic gunsight, courtesy of an Eduard Spitfire kit. Decals from Xtradecal sheet 48-127, paints by Colourcoats, applied with a Sparmax Max4 airbrush.
  3. Gloster Meteor FR.9, WX978, 2 (AC) Sqn, RAF, Gütersloh, May 1953. 1/48 Airfix kit (A09188), assembled SFTB, paints by Colourcoats and Humbrol. Onwards and Upwards!
  4. Not really. The 'trick' seems to be to leave the final cementing of the cockpit interior - and particularly the IP - until you have wiggled/coerced/hammered the tank cover into place.
  5. Spitfire LF Mk.Vc Trop., JK345 336 (Greek) Sqn, RAF, Greece 1944. Airfix Mk.Vb with Alley Cat Mk.Vc conversion, markings from Xtradecal #48150, paint from Tamiya and Colourcoats
  6. In the Programme above, it's a 20 second clip from 14'30"-ish.
  7. Hannants have black 8" serials on Xtradecal X32021 They also have Sky codes on Xtradecal X32023 (24" codes) and Xtradecal X32024 (30" codes) Should you be in need of MSG codes, they are also available. Usual disclaimers - I have no connection with Hannants other than as a satisfied customer. HTH Ian
  8. See here for details : http://hgwmodels.cz/en/content/18-wet-transfers
  9. Are you sure it's a Brewer? As far as I know, only the Firebar has been released thus far. I confess that I omitted the parts you mention from my Firebar build, and I installed the undercarriage legs as the instructions suggested, although I left off the wheels until much later. Ian
  10. Thanks for the inspiration, Sean. I'm in the clamping/gluing,scraping/filling/sanding cycle with mine at the moment. You've given me strength to carry on!
  11. I have always been fascinated by those strange Soviet aircraft, that appeared only as blurred images in the days of my youth. I have recently been intrigued by Spencer Pollard's explanation of how he approaches natural metal finishes. I therefore decided to 'give it a go'. This is Trumpeter's 1/48th Sukhoi Su-11 "Fishpot". It's OOB, except for some stencilling on the 'Anab' missiles, masking tape belts, and a bit of 'creative gizmology' under the canopy. It took eight days, start to finish, devoting a couple of hours a day. Is it accurate? I don 't know - and, to be honest, I don't really care. It looks like I hoped it would. TLAR! Enjoy!
  12. This is the Tan Model kit, built strictly OOB - no aftermarket, no scratch-building, no detailing. Heck, I even used the kit decals! All in all, a much more pleasant experience than I had anticipated. Such minor glitches as I encountered were of my doing - the kit is lovely. Enjoy . . . Keep bashing the plastic!
  13. Just a tip - if you,re using Word, or any other DTP/WP program, each 'point' in print size equates to 1/72 of an inch. Thus, 10 pt lettering will give you 10" serials in 1/72 scale (and 15 pt will give you 10" serials in 1/48). Suitable fonts are downloadable here. HTH
  14. It must be a Lincolnshire thing! Mine also arrived this morning, hassle- and extra charge- free, and looking every bit as good as I hoped. I predict an imminent orgy of Alclad!
  15. In 1946, the Air Ministry and the Admiralty issued the specifications F.44/46 and N.40/46 for a twin-engined, two-seat long range fighter. De Havilland responded with their de Havilland 110, and Gloster with their GA.5. The RAF expressed an interest in the de Havilland project, and a number of prototypes were ordered. The Navy rejected both proposals, and opted for an enhanced Sea Venom. Gloster lobbied successfully, and prototypes of their tailed delta design were also ordered, even though the de Havilland design seemed more promising. By 1951, the dH 110 was well into its test programme, regularly flying supersonically, while the GA.5 (Javelin) was plagued by flutter and other aerodynamic problems. Then, at the Farnborough Air Show on 6th September 1952, the dH 110 prototype WG236 broke up in transonic flight, with the engines and forward fuselage ploughing into the crowd, killing the crew and 29 spectators, and severely injuring more than 60 others. The RAF switched its attentions to the Javelin, and four years later, the Navy accepted a navalised dH 110 as the Sea Vixen. But what if . . . If John Derry had flown his display without incident, the Air Ministry’s choice may well have alighted on the de Havilland design. It was aerodynamically superior to the Javelin, which was thick-winged and draggy, with inadequate pitch control and engines buried so deeply in the fuselage that power losses in the intakes and exhausts emasculated them. The Vixen, on the other hand, was aerodynamically cleaner, with a relatively thin wing, and offered potential advantages in range, speed and acceleration. It was also cleared for use of the Firestreak and Red Top Missile much earlier than was the Javelin. If the RAF had gone with the Vixen, by 1970 they might have ended up with this: de Havilland Vixen F(AW).5, 11 Sqn, RAF, Geilenkirchen, 1970. Enjoy! Ian
  16. Kiwi Resin (http://www.kiwiresin.com) do a F-86A conversion with the requisite wing mods, and it's entirely possible that Dave (Lockhead) would consider letting you buy just the wing parts. Apart from the increasingly rare Cutting Edge set, there used to be one from Scobiedo Productions, but I haven't seen it for ages. You can use the wings from Revell/Monogram's F-86D, but be warned that the sweep angles don't match! Good Luck! Ian
  17. Here is the recent Airfix 1/48th Meteor F.8 in target-towing colours, as seen at RAF Sylt in the late '50's. Decals are from the excellent Xtradecal sheet, and paint from Colourcoats, Humbrol and Mr Paint. It's a lovely kit to build, but beware of a very fragile windscreen (you may notice the crack in mine). I have a replacement ordered, but it's currently unavailable. Thanks for looking, Ian
  18. So, I read the books, trawl the web, look at the photographs, gather and print the necessary decals, and start the model. It goes quite smoothly (with one noticeable masking glitch), and at last it's finished. And as I'm admiring my handiwork, I get a chatty email from a friend who is modelling the same aeroplane, and who refers me to the photo below : Now I'm sure that I had already seen that picture, but I had completely missed the oversize fuselage roundel! So now I have a dilemma, which I think I'll deal with by 'sleeping on it' for a while, after which I may choose to 'revise' the rear fuselage. In the meantime, here is my (not terribly accurate) model of L7005, the most successful Defiant of all Thanks for looking, Ian
  19. Just such a spreadsheet is in preparation, via the Spitfire SIG of IPMS/UK. I had hoped to have it complete and online by this year's SMW, but life - in the form of a lengthy illness - got in the way. I'll post on here when it finally sees the light of day. Ian (Spitfire SIG Leader)
  20. Here is the venerable Eduard 1/48th Tempest V, converted to a Tempest Mk.II, using Airwaves' equally ancient resin conversion and AlleyCat's rear fuselage correction. I also added SAC's metal u/c legs, to overcome the Eduard kit's inherent wobbles, and Barracuda's excellent resin wheels. Paint by Tamiya and decals by Model Alliance. This model was started nearly twenty years ago - I bought the Mk.II conversion from ED Models on the way home from an IPMS AGM at Ladywood (and now I'm showing my age!) - but I dragged it out of the oubliette beneath my bench and 'cracked on'! It's a 16 Sqn machine, based at Fassberg in 1947, and the model should be appearing in the RAF Germany SIG display at this year's shows. Enjoy . . .
  21. Assuming that you're working in 1/48th, Freightdog have this sheet on offer at the moment. http://www.freightdogmodels.co.uk/images/FSD48006X.jpg
  22. Troy Smith wrote . . . ". . . and one I keep seeing, the roundels are too far outboard. the centre of the roundel is 80 inches inboard from the wingtip according to the Ducimus Camo diagram. As the roundel is 49", the edge should be 55.5" from tip. In 1/48th this is near as dammit 30mm, or just align on aileron and panel line. " I retrieved the Hurricane from its shelf, where it awaits weathering and antenna wire, and did some measuring. The centres of the upper roundels are, as accurately as I can measure, one and five eighths of an inch from the tip, which equates to 78" full size, so my error was to place them just about a millimetre too far outboard. I'll live with that! Ian
  23. Troy, thanks for the comments. It's the new kit, with markings from the Kagero 'Battle of Britain' book/decals. I wish I'd seen that photo before I placed the codes, and as regards the upperwing roundels - mea culpa. The Ducimus series are normally an early point of reference, but I worked on the basis that the roundels were to be so positioned that they cleared the leading edge and the aileron hinge line by between 1 and 2 scale inches, which I seem to remember being the original guidance. Perhaps the roundels are marginally undersized? I shall check!
  24. She scrubs up quite nicely . . . Ian.
×
×
  • Create New...